Home » Panasonic Manuals » Video Cameras » Panasonic HPX300 » Manual Viewer

Panasonic HPX300 Operating Instructions - Page 51

Setting the Electronic Shutter, Setting the Shutter Mode and Speed

UPC - 791871304297

Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Setting the Electronic Shutter Setting the Shutter Mode and Speed 1 Press the SHUTTER switch positioned at OFF towards ON. Viewfinder displays relating to the shutter See [Vie wfinder Screen Status Displays] (page 65). Placing the Camera-recorder in SYNCHRO SCAN Mode To place the camera-recorder in SYNCHRO SCAN mode, follow the steps below. 1 Press the SHUTTER switch positioned at ON towards SEL, to place the camera-recorder in SYNCHRO SCAN (S/S) mode. Chapter 4 Adjustments and Settings for Recording SHUTTER switch 2 Press the SHUTTER switch towards [SEL]. Repeat this switchover until the desired mode or speed appears in the viewfinder screen. • If all modes and speeds are available, the display changes in the following order: For 60i and 60P recording S/S (1/15) (1/30) 1/60 1/100 1/120 1/250 1/500 1/1000 1/2000 For 30P recording S/S (1/7.5) (1/15) 1/60 1/100 1/120 1/250 1/500 1/1000 1/2000 For 24P recording S/S (1/6) (1/12) 1/60 1/100 1/120 1/250 1/500 1/1000 1/2000 • The bracketed ( ) speeds cannot be selected when VFR is ON.  NOTE • In any electronic shutter mode, a slower shutter speed will reduce camera sensitivity. • In auto iris mode, a faster shutter speed will increase the aperture and lower the depth of field. • Changes in synchro scan and shutter speed settings may cause screen flicker. • Under fluorescent lighting and other discharge lighting systems, horizontal stripes may appear on the screen. Changing the shutter speed may correct this problem. • A subject that is captured when moving quickly across the field of view may appear distorted. This is due to the signal read out format of the image sensor (MOS sensor) and is not a malfunction. • The red, blue and green dots that may appear on the screen at low shutter speeds do not indicate a malfunction. SHUTTER switch SYNCHRO SCAN switch 2 In SYNCHRO SCAN mode, use the SYNCHRO SCAN switch to make stepless changes in the range between 1/60.0 s and 1/249.8 s (for 60i mode). • Hold down the SYNCHRO SCAN switch to speed up the rate of shutter speed changes. If shutter speed changes stop before the desired shutter speed has been reached, press again to continue changing shutter speeds. Range of variation in each mode • 60P/60i mode: 1/60.0 to 1/249.8 • 30P/30PN mode: 1/30.0 to 1/249.8 • 24P/24PA/24PN mode: 1/24.0 to 1/249.8 • When the SYNC SCAN DISP option in DISPLAY SETUP is set to deg: 3.0d to 359.5d • If SYSTEM MODE setting is changed, shutter speed may also be changed. Setting the menu option SYNC SCAN DISP in the DISPLAY SETUP screen to deg provides a guide to setting and displaying shutter angle. 51

Section	Page
Read this first!	2
Precautions for Use	4
Chapter 1 Overview	8
Camera Unit Features	8
Recording and Playback Features	10
Outline of operations	12
Saving and editing on external devices	12
System Conﬁguration	13
Standard accessories	14
Chapter 2 Parts and Their Functions	15
Power Supply and Accessory Mounting Section	15
Audio (input) Function Section	16
Audio (output) Function Section	17
Shooting and Recording/Playback Functions Section	18
Menu/Thumbnail Operation Section	22
Time Code Section	23
Warning and Status Display Functions	24
LCD Monitor	24
Viewfinder	25
Chapter 3 Recording and Playback	26
Setting Date and Time of Internal Clock	26
P2 Cards	28
Inserting P2 Cards	28
Removing P2 Cards	28
To Prevent Accidental Erasure of P2 Card Content	29
P2 CARD ACCESS LED and status of P2 cards	29
P2 card recording times	30
Handling P2 Card Recording	31
Basic Procedures	32
Shooting	33
Normal Recording	33
Standard and Native Recording	34
Standard recording (pull-down recording)	34
Native recording	34
Variable Frame Rate (VFR) Recording	35
Native VFR Recording	35
Standard VFR recording(pulldown recording)	35
Using VFR Recording Function	36
Special Recording Modes	38
Pre-recording (PRE REC)	38
Interval recording (INTERVAL REC)	39
One-shot recording (ONE SHOT REC)	39
Loop recording (LOOP REC)	40
PROXY Recording Function (Optional)	40
Hot Swap Recording	40
REC REVIEW Function	40
Shot Marker (SHOT MARK) Recording Function	41
Text Memo Recording Function	41
Normal and Variable Speed Playback	42
Chapter 4 Adjustments and Settings for Recording	43
Selecting recording signals	43
List of recording formats and functions	44
Recording settings and recording function table	45
Selecting video output	45
List of recording, playback and output formats	46
Adjusting the White Balance and Black Balance	48
Adjusting the White Balance	48
Adjusting the Black Balance	49
Setting the Electronic Shutter	51
Setting the Shutter Mode and Speed	51
Placing the Camera-recorder in SYNCHRO SCAN Mode	51
FBC (Flash Band Compensation) Function	52
Setting FBC function	52
Assigning functions to USER buttons	53
Selecting Audio Input Signals and Adjusting Recording Levels	54
Selecting Audio Input Signals	54
Adjusting Recording Levels	54
Selecting Function for the FRONT AUDIO LEVEL Control	55
CH3 and CH4 Recording Levels	55
Setting Time Data	56
Recording time codes and user bits	57
Setting user bits	58
Entering the User Bits	58
Setting the Time Code	60
Externally Locking the Time Code	62
Outputting the time code externally	63
GENLOCK and time code input/output connection and setup	64
Counter Setting and Display	64
Viewfinder Screen Status Displays	65
Viewfinder Status Indication Layout	65
Selecting Viewfinder Display Information	65
Screen displays	66
Center Information Display	69
Checking and displaying shooting status	71
MODE CHECK indication	72
Center marker display	73
Safety zone markers	73
Audio level meter magnification	73
Zebra pattern display	74
Focus assist function	75
Adjusting and setting the LCD monitor	76
Waveform monitor function	77
Adjusting and Setting up the Viewfinder	78
Adjusting Right and Left Viewfinder Position	78
Diopter Adjustment	78
Using the Viewfinder	78
Emphasizing Image Outlines	79
Setting the viewfinder to monochrome mode	79
Handling setup data	80
Configuration of setup data files	80
Handling SD memory cards	81
Formatting, Writing and Reading an SD memory card	81
How to Use Scene File Data	82
Saving scene files and other settings on SD memory cards	84
Chapter 5 Preparation	86
Power Supply	86
Mounting the Battery and Setting the Battery Type	86
Use of the external DC power supply	88
Mounting and Adjusting the Lens	89
Mounting the Lens	89
Adjusting the Lens Flange Back	90
White Shading Compensation	91
Setting Chromatic Aberration Compensation (CAC)	92
Preparing for Audio Input	95
When Using the Front Microphone	95
Using a wireless receiver	95
When Using Audio Devices	96
Attaching Accessories	97
Mounting the Camera on a Tripod	97
Attaching the Shoulder Strap	97
Attaching the Rain Cover	98
Attaching the FRONT AUDIO LEVEL Control Knob	98
Attaching the Eye Cup	98
DC OUT Connector and External REC Start/Stop Switch Connection	99
Connecting the AJ-RC10G Remote Controller	100
Chapter 6 Manipulating Clips with Thumbnails	101
Thumbnail Operations	101
Thumbnail Manipulations Overview	101
Thumbnail Screen	102
Selecting Thumbnails	104
Playing back Clips	104
Switching the Thumbnail Display	105
Changing thumbnails	106
Shot Mark	106
Text Memo	107
Deleting Clips	108
Restoring Clips	109
Reconnection of Incomplete Clips	109
Copying Clips	109
Setting of Clip Meta Data	110
Setting of Proxy (optional)	114
Formatting a P2 Card	114
Formatting SD memory cards	115
Setting the Thumbnail Display Mode	115
Properties	116
Chapter 7 Menu Operations	120
Viewfinder and LCD Menus	120
Using the menus	120
Initializing the menu settings	121
Setup menu structure	122
Setup menu list	124
SCENE FILE screen	124
SYSTEM SETUP screen	126
SW MODE screen	128
RECORDING SETUP screen	129
AUDIO SETUP screen	130
OUTPUT SEL screen	132
DISPLAY SETUP screen	132
BATTERY SETUP screen	134
CARD FUNCTIONS screen	136
LENS SETUP screen	136
OTHER FUNCTIONS screen	137
DIAGNOSTIC screen	138
OPTION MENU screen	138
Chapter 8 Connecting to External Devices	139
Functionality Provided by Connections to USB 2.0 Connector	139
Connecting to a computer in USB device mode	139
USB host mode	140
Connections to the DVCPRO/DV Connector	145
Recording signals input to the DVCPRO/DV connector	145
Control of external devices through 1394 connection	146
Chapter 9 Maintenance and Inspections	147
Inspections Before Shooting	147
Preparing for Inspections	147
Inspecting the Camera Unit	147
Inspecting the Memory Recording Functions	148
Maintenance	150
Eyepiece Care	150
Cleaning Inside the Viewfinder	150
Charging the internal battery	150
Warning System	151
Warning Description Tables	151
Warning and Error Display for Thumbnail Operation and USB HOST MODE	153
Updating the firmware incorporated into the unit	155
Chapter 10 Index	156
Chapter 11 Specifications	160
Dimensions and specifications	160
Dimensions	160
Specifications	160

Match case Limit results 1 per page

µ1

Chapter²´² Adjustments²and²Settings²for²Recording

Setting the Electronic Shutter

Setting the Shutter Mode and

Speed

Press²the²SHUTTER²switch²positioned²at²OFF²

towards²ON.

SHUTTER²switch

Press²the²SHUTTER²switch²towards²[SEL].²

Repeat²this²switchover²until²the²desired²mode²

or²speed²appears²in²the²viewﬁnder²screen.

• If all modes and speeds are available, the display

changes in the following order:

For²¶0i²and²¶0P²recording

(1/15)

(1/30)

1/60

1/100

1/250

S/S

1/120

1/500

1/1000

1/2000

For²³0P²recording

(1/7.5)

(1/15)

1/60

1/100

1/250

S/S

1/120

1/500

1/1000

1/2000

For²±´P²recording

(1/6)

(1/12)

1/60

1/100

1/250

S/S

1/120

1/500

1/1000

1/2000

• The bracketed (

) speeds cannot be selected

when VFR is ON.



NOTE

• In any electronic shutter mode, a slower shutter speed will

reduce camera sensitivity.

• In auto iris mode, a faster shutter speed will increase the

aperture and lower the depth of ﬁeld.

• Changes in synchro scan and shutter speed settings may

cause screen ﬂicker.

• Under ﬂuorescent lighting and other discharge lighting

systems, horizontal stripes may appear on the screen.

Changing the shutter speed may correct this problem.

• A subject that is captured when moving quickly across the

ﬁeld of view may appear distorted. This is due to the signal

read out format of the image sensor (MOS sensor) and is not

a malfunction.

• The red, blue and green dots that may appear on the screen

at low shutter speeds do not indicate a malfunction.

Viewﬁnder displays relating to the shutter

See [Vie wﬁnder Screen Status Displays] (page 65).

Placing the Camera-recorder in

SYNCHRO SCAN Mode

To place the camera-recorder in SYNCHRO SCAN mode,

follow the steps below.

Press²the²SHUTTER²switch²positioned²at²ON²

towards²SEL,²to²place²the²camera-recorder²in²

SYNCHRO²SCAN²(S/S)²mode.

SHUTTER²switch

SYNCHRO²SCAN²switch

In²SYNCHRO²SCAN²mode,²use²the²SYNCHRO²

SCAN²switch²to²make²stepless²changes²in²the²

range²between²1/¶0.0²s²and²1/±´¹.¸²s²(for²¶0i²

mode).

•²²

Hold²down²the²SYNCHRO²SCAN²switch²to²speed²

up²the²rate²of²shutter²speed²changes.

If²shutter²speed²changes²stop²before²the²desired²

shutter²speed²has²been²reached,²press²again²to²

continue²changing²shutter²speeds.

Range of variation in each mode

• 60P/60i mode: 1/60.0 to 1/249.8

• 30P/30PN mode: 1/30.0 to 1/249.8

• 24P/24PA/24PN mode: 1/24.0 to 1/249.8

• When the SYNC SCAN DISP option in DISPLAY SETUP is

set to deg: 3.0d to 359.5d

• If SYSTEM MODE setting is changed, shutter speed may

also be changed.

Setting²the²menu²option²SYNC²SCAN²DISP²in²the²DISPLAY²

SETUP²screen²to²deg²provides²a²guide²to²setting²and²

displaying²shutter²angle.