Panasonic HPX300 Operating Instructions - Page 87

When using a V-mount type battery, When using an NP battery, Preparation

Page 87 highlights

Chapter 5 Preparation When using a V-mount type battery Mount the V-mount adapter plate. Insert the plate and slide it as shown below. • To remove the plate, slide the release lever downwards. When using an NP battery 1 Mount a V-mount adapter plate on the camera. Refer to [When using a V-mount type battery] (this page). Release lever 2 Attach a holder plate on the NP battery case. • When the battery plate comes with a packing, first insert the packing in the battery case. (1) R emove the screw at the bottom of the cover and remove the cover. (2) L ine up the openings in the battery case and battery plate and use the supplied screws to fasten the case to the plate. (3) T ighten the power supply connector screw. (4) Insert the removed top cover in the direction of the arrow. (5) L ine up the openings in the lower cover (metal part) and the case and use the securing screw to fasten them together.  Setting the battery type • Select the battery type listed under BATTERY SELECT. Select the menu option BATTERY SELECT from the setting menu BATTERY SETUP screen. • When using a battery not listed under BATTERY SELECT: If it is a NiCd battery, select "NiCd14(14V)" and set each item according to the battery characteristics. If it is not a NiCd battery, select TYPE A or TYPE B and set each item according to the battery characteristics. For details, refer to [BATTERY SETUP screen] (page 134).  NOTE • For information about the V-mount adapter plate, please contact the store where you purchased the camera-recorder. • With the V-mount adapter plate installed, % (percent) values cannot be displayed when using batteries that show the remaining battery capacity.    87

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166

¸·
Chapter²µ² Preparation
When using a V-mount type battery
Mount the V-mount adapter plate. Insert the plate and slide
it as shown below.
• To remove the plate, slide the release lever downwards.
Release²lever
Setting the battery type
• Select the battery type listed under BATTERY SELECT.
Select the menu option BATTERY SELECT from the
setting menu BATTERY SETUP screen.
• When using a battery not listed under BATTERY SELECT:
If it is a NiCd battery, select “NiCd14(14V)” and set each
item according to the battery characteristics. If it is not a
NiCd battery, select TYPE A or TYPE B and set each item
according to the battery characteristics. For details, refer
to [BATTERY SETUP screen] (page 134).
NOTE
• For information about the V-mount adapter plate, please
contact the store where you purchased the camera-recorder.
• With the V-mount adapter plate installed, % (percent) values
cannot be displayed when using batteries that show the
remaining battery capacity.
When using an NP battery
1
²
Mount²a²V-mount²adapter²plate²on²the²camera.²
Refer to [When using a V-mount type battery] (this
page).
2
²
Attach²a²holder²plate²on²the²NP²battery²case.²
• When the battery plate comes with a packing, first
insert the packing in the battery case.
(1) Remove the screw at the bottom of the cover
and remove the cover.
(2) Line up the openings in the battery case and
battery plate and use the supplied screws to
fasten the case to the plate.
(3) Tighten the power supply connector screw.
(4) Insert the removed top cover in the direction of
the arrow.
(5) Line up the openings in the lower cover (metal
part) and the case and use the securing screw
to fasten them together.