Panasonic WVCU650 Operating Instructions - Page 23

Group Address Setting for System, Controller, Units, PS Data Com. Setup, Cnt G-Adr.B

Get Panasonic WVCU650 - SYSTEM CONTROLLER ADDENDUM PDF manuals and user guides
UPC - 791871504277
View all Panasonic WVCU650 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

● Group Address Setting for System Controller Note: Remain the factory default. When you have mistakenly changed the setting, recover the factory default as follows. 1. Select "Cnt G-Adr." by rotating the JogDial. (Refer to Step 5 in p. 21.) 2. Press the CAM (SET) button. The LCD display will change from the display mode to the editing mode. PS • Data Com. Setup Cnt G-Adr.B 3. Select a desired parameter by rotating the JogDial or pressing the + or - button. You can select the desired parameter from "A" to "Z". The factory default is "A". PS • Data Com. Setup Cnt G-Adr.A 4. Press the MON (ESC) button. The selected parameter will be determined, and the LCD display will return to the display mode. PS • Data Com. Setup Cnt G-Adr.A ● Group Address Setting for System Units Note: Remain the factory default. When you have mistakenly changed the setting, recover the factory default as follows. 1. Select "Sys G-Adr." by rotating the JogDial. (Refer to Step 5 in p. 21.) 2. Press the CAM (SET) button. The LCD display will change from the display mode to the editing mode. PS • Data Com. Setup Sys G-Adr.B 3. Select "A" by rotating the JogDial or pressing the + or - button. PS • Data Com. Setup Sys G-Adr.A 4. Press the CAM (SET) button. The parameter will be determined, and the cursor will jump to the sub parameter. PS • Data Com. Setup Sys G-Adr.A 05 5. Enter the unit number of system unit by rotating the JogDial or pressing the + or - button. PS • Data Com. Setup Sys G-Adr.A 01 Note: 1 to 99 is available for the unit number. The factory default is 01. 6. Press the CAM (SET) button. The sub parameter will be determined, and "OK" will appear on the LCD. PS • Data Com. Setup Sys G-Adr.A 01 OK After a second, the LCD display will return to the status in Step 5. If you set the unit numbers of other system units, repeat Step 5. Note: If the parameters cannot be determined, "NG" will appear on the LCD. In this case, check the unit number of system unit, and repeat Step 3 to 6. 7. Press the MON (ESC) button. The LCD display will return to the status in Step 2. 8. Press the MON (ESC) button again. The LCD display will return from the editing mode to the display mode. 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
23
●
Group Address Setting for System
Controller
Note:
Remain the factory default. When you have mistaken-
ly changed the setting, recover the factory default as
follows.
1.
Select “Cnt G-Adr.” by rotating the JogDial.
(Refer to Step 5 in p. 21.)
2.
Press the CAM (SET) button.
The LCD display will change from the display mode to
the editing mode.
3. Select a desired parameter by rotating the JogDial
or pressing the + or – button.
You can select the desired parameter from “A” to “Z”.
The factory default is “A”.
4.
Press the MON (ESC) button.
The selected parameter will be determined, and the
LCD display will return to the display mode.
●
Group Address Setting for System
Units
Note:
Remain the factory default. When you have mistaken-
ly changed the setting, recover the factory default as
follows.
1.
Select “Sys G-Adr.” by rotating the JogDial.
(Refer to Step 5 in p. 21.)
2.
Press the CAM (SET) button.
The LCD display will change from the display mode to
the editing mode.
3. Select "A" by rotating the JogDial or pressing the +
or – button.
4.
Press the CAM (SET) button.
The parameter will be determined, and the cursor will
jump to the sub parameter.
5.
Enter the unit number of system unit by rotating the
JogDial or pressing the + or – button.
Note:
1 to 99 is available for the unit number. The facto-
ry default is 01.
6.
Press the CAM (SET) button.
The sub parameter will be determined, and "OK" will
appear on the LCD.
After a second, the LCD display will return to the status
in Step 5.
If you set the unit numbers of other system units, repeat
Step 5.
Note:
If the parameters cannot be determined, "NG" will
appear on the LCD. In this case, check the unit
number of system unit, and repeat Step 3 to 6.
7.
Press the MON (ESC) button.
The LCD display will return to the status in Step 2.
8.
Press the MON (ESC) button again.
The LCD display will return from the editing mode to the
display mode.
•
PS Data Com. Setup
Cnt G—Adr.B
•
PS Data Com. Setup
Cnt G—Adr.A
•
PS Data Com. Setup
Cnt G—Adr.A
•
PS Data Com. Setup
Sys G—Adr.B
•
PS Data Com. Setup
Sys G—Adr.A
•
PS Data Com. Setup
Sys G—Adr.A
05
•
PS Data Com. Setup
Sys G—Adr.A
01
•
PS Data Com. Setup
Sys G—Adr.A
01
OK