Sony STR-DN1010 Operating Instructions - Page 107

To operate on the receiver, To cancel Auto Calibration, To confirm/save Auto

Get Sony STR-DN1010 - Multi Channel Av Receiver PDF manuals and user guides
UPC - 027242779945
View all Sony STR-DN1010 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 107 highlights

Performing Auto Calibration For details on the Auto Calibration, see "Calibrating the appropriate speaker settings automatically (Auto Calibration)" (page 38). See "Before you perform Auto Calibration" (page 38) before performing the Auto Calibration. To operate on the receiver 1 Press GUI MODE repeatedly to select "MENU OFF". 2 Press AMP. Receiver operation is enabled. 3 Press MENU. 4 Press V/v repeatedly to select "" , then press or b. 5 Press V/v repeatedly to select "A.CAL START", then press to start the measurement. Measurement starts in 5 seconds. A count down is displayed. Note While the time is counting down, stand away from the measurement area to avoid measurement error. 6 Measurement starts. The measurement process will take approximately 30 seconds. Wait until the measurement process completes. To cancel Auto Calibration The Auto Calibration function will be canceled when you do the following during the measurement process: - Press ?/1. - Press the input buttons on the remote or press the INPUT SELECTOR +/- repeatedly on the receiver. - Press MUTING (RM-AAP051 only) or (RM-AAP052 only) on the remote. You can also use MUTING on the receiver. - Press SPEAKERS on the receiver. - Change the volume level. - Connect the headphones. Tips • Operations other than turning the receiver on or off are deactivated during Auto Calibration. • The measurements may not be performed correctly or Auto Calibration cannot be performed when special speakers, such as dipole speakers are used. To confirm/save Auto Calibration results when GUI function is turned off 1 Confirm the measurement result. When the measurement ends, a beep sounds and the measurement result appears on the display. Measurement process Explanation [Display] Completes properly [SAVE EXIT] Proceed to step 2. Fails [E - xxxa):xxb)] See "Message list after Auto Calibration measurement" (page 43). a)xxx represent a speaker channel. F Front S Surround SB Surround back FH Front high Depending on the error code, the speaker channel may not appears. b)xx represent an error code. Advanced Operations continued 107GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
107
GB
Advanced Operations
For details on the Auto Calibration, see
“Calibrating the appropriate speaker settings
automatically (Auto Calibration)” (page 38).
See “Before you perform Auto Calibration”
(page 38) before performing the Auto
Calibration.
To operate on the receiver
1
Press GUI MODE repeatedly to select
“MENU OFF”.
2
Press AMP.
Receiver operation is enabled.
3
Press MENU.
4
Press
V
/
v
repeatedly to select “<AUTO
CAL>” , then press
or
b
.
5
Press
V
/
v
repeatedly to select “A.CAL
START”, then press
to start the
measurement.
Measurement starts in 5 seconds. A count
down is displayed.
Note
While the time is counting down, stand away
from the measurement area to avoid
measurement error.
6
Measurement starts.
The measurement process will take
approximately 30 seconds. Wait until the
measurement process completes.
To cancel Auto Calibration
The Auto Calibration function will be
canceled when you do the following during the
measurement process:
– Press
?
/
1
.
– Press the input buttons on the remote or
press the INPUT SELECTOR +/–
repeatedly on the receiver.
– Press MUTING (RM-AAP051 only) or
(RM-AAP052 only) on the remote. You can
also use MUTING on the receiver.
– Press SPEAKERS on the receiver.
– Change the volume level.
– Connect the headphones.
Tips
• Operations other than turning the receiver on or off
are deactivated during Auto Calibration.
• The measurements may not be performed correctly
or Auto Calibration cannot be performed when
special speakers, such as dipole speakers are used.
To confirm/save Auto
Calibration results when GUI
function is turned off
1
Confirm the measurement result.
When the measurement ends, a beep
sounds and the measurement result appears
on the display.
a)
xxx
represent a speaker channel.
F
Front
S
Surround
SB
Surround back
FH
Front high
Depending on the error code, the speaker
channel may not appears.
b)
xx
represent an error code.
Performing Auto Calibration
Measurement process
[Display]
Explanation
Completes properly
[SAVE EXIT]
Proceed to step 2.
Fails
[
E -
xxx
a)
:
xx
b)
]
See “Message list
after Auto
Calibration
measurement”
(page 43).
continued