Yamaha RX V661 MCXSP10 Manual - Page 29

Setting the speaker impedance, Turning this unit on and off, standby mode. - remote control

Get Yamaha RX V661 - AV Receiver PDF manuals and user guides
UPC - 027108927411
View all Yamaha RX V661 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

PREPARATION Connections Setting the speaker impedance Caution If you are to use 6 ohm speakers, set "SP IMP." to "6Ω MIN" as follows BEFORE using this unit. 4 ohm speakers can be also used as the front speakers. 1 Make sure this unit is turned off. Refer to the right column for details. 2 Press and hold CTONE CONTROL on the front panel and then press BMASTER ON/ OFF inward to the ON position to turn on this unit. This unit turns on, and the advanced setup menu appears in the front panel display. TONE CONTROL While holding down MASTER ON OFF 3 Rotate the DPROGRAM selector on the front panel to select "SP IMP.". "SP IMP." and the current speaker impedance setting ("8Ω MIN") appear in the front panel display. 4 Press CTONE CONTROL on the front panel repeatedly to select "6Ω MIN". 5 Press BMASTER ON/OFF on the front panel to release it outward to the OFF position to save the new setting and turn off this unit. Note The setting you made is reflected next time you turn on this unit. Turning this unit on and off ■ Turning on this unit Press BMASTER ON/OFF on the front panel inward to the ON position to turn on this unit. When you turns on this unit by pressing BMASTER ON/OFF, the main zone is turned on. y When you turn on this unit, there will be a 4 to 5-second delay before this unit can reproduce sound. ■ Turning off this unit Press BMASTER ON/OFF on the front panel again to release it outward to the OFF position to turn off this unit. Notes • AMAIN ZONE ON/OFF on the front panel as well as HPOWER and GSTANDBY on the remote control are operational only when BMASTER ON/OFF is pressed inward to the ON position. • As usual, we recommend using the standby mode to turn off this unit. ■ Set the main zone to the standby mode Press AMAIN ZONE ON/OFF (or GSTANDBY) to set the main zone to the standby mode. In the standby mode, this unit consumes a small amount of power in order to receive infrared signals from the remote control. ■ Turning on the main zone from the standby mode Press AMAIN ZONE ON/OFF (or HPOWER) to turn on the main zone. y • You can also turn on the main zone by pressing FSCENE (or FSCENE) buttons. • When you turn on this unit, there will be a 4 to 5-second delay before this unit can reproduce sound. • These buttons are operational only when BMASTER ON/ OFF is pressed inward to the ON position. English 25 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
25
En
Connections
PREPARATION
English
1
Make sure this unit is turned off.
Refer to the right column for details.
2
Press and hold
C
TONE CONTROL
on the
front panel and then press
B
MASTER ON/
OFF
inward to the ON position to turn on this
unit.
This unit turns on, and the advanced setup menu
appears in the front panel display.
3
Rotate the
D
PROGRAM
selector on the
front panel to select “SP IMP.”.
“SP IMP.” and the current speaker impedance setting
(“8
Ω
MIN”) appear in the front panel display.
4
Press
C
TONE CONTROL
on the front
panel repeatedly to select “6
Ω
MIN”.
5
Press
B
MASTER ON/OFF
on the front
panel to release it outward to the OFF
position to save the new setting and turn off
this unit.
The setting you made is reflected next time you turn on this
unit.
■
Turning on this unit
Press
B
MASTER ON/OFF
on the front panel
inward to the ON position to turn on this
unit.
When you turns on this unit by pressing
B
MASTER
ON/OFF
, the main zone is turned on.
y
When you turn on this unit, there will be a 4 to 5-second delay
before this unit can reproduce sound.
■
Turning off this unit
Press
B
MASTER ON/OFF
on the front panel
again to release it outward to the OFF
position to turn off this unit.
•
A
MAIN ZONE ON/OFF
on the front panel as well as
H
POWER
and
G
STANDBY
on the remote control are
operational only when
B
MASTER ON/OFF
is pressed
inward to the ON position.
•
As usual, we recommend using the standby mode to turn off this
unit.
■
Set the main zone to the standby mode
Press
A
MAIN ZONE ON/OFF
(or
G
STANDBY
) to set the main zone to the
standby mode.
In the standby mode, this unit consumes a small amount of
power in order to receive infrared signals from the remote
control.
■
Turning on the main zone from the
standby mode
Press
A
MAIN ZONE ON/OFF
(or
H
POWER
)
to turn on the main zone.
y
•
You can also turn on the main zone by pressing
F
SCENE
(or
F
SCENE
) buttons.
•
When you turn on this unit, there will be a 4 to 5-second delay
before this unit can reproduce sound.
•
These buttons are operational only when
B
MASTER ON/
OFF
is pressed inward to the ON position.
Setting the speaker impedance
Caution
If you are to use 6 ohm speakers, set “SP IMP.” to
“6
Ω
MIN” as follows BEFORE using this unit. 4 ohm
speakers can be also used as the front speakers.
Note
TONE CONTROL
MASTER
ON
OFF
While holding
down
Turning this unit on and off
Notes