3Com 3CCFEM556B User Guide - Page 39

Running the Point Enabler Under DOS

Get 3Com 3CCFEM556B - Megahertz 10/100 LAN PDF manuals and user guides
UPC - 662662532154
View all 3Com 3CCFEM556B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Running the Point Enabler Under DOS 33 Follow these steps to exclude a sample 8 K memory range: 1 Make a backup copy of the CONFIG.SYS file. 2 Use a text editor to edit the CONFIG.SYS file on your computer. 3 Exclude the memory range that the LAN+Modem card is using. For example, type this line in the CONFIG.SYS file: device=c:\windows\emm386.exe NOEMS x=DE00-DFFF (8k) where x stands for exclude, followed by an 8K contiguous block of memory. In this example, the memory setting is DE00-DFFF. Refer to the manual that accompanied the memory manager software for additional instructions and information. 4 Save the CONFIG.SYS file and exit the text editor. 5 Reboot the computer. Running the Point Enabler Under DOS For NetWare networking environments, the point enabler should be installed in the AUTOEXEC.BAT file. Make sure that the point enabler program, FMENABLE.EXE, is listed before the ODI driver. The AUTOEXEC.BAT file should contain the line: fmenable.exe For NDIS networking environments, the point enabler should be installed in the CONFIG.SYS file. Make sure the that the point enabler program is listed before the NDIS driver. The CONFIG.SYS file should contain the line: device=c:\nwclient\fmenable.exe Alternatively, you can run the configuration manager manually from DOS each time you use the modem by typing: fmenable [Enter]

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Running the Point Enabler Under DOS
33
Follow these steps to exclude a sample 8 K memory range:
1
Make a backup copy of the CONFIG.SYS file.
2
Use a text editor to edit the CONFIG.SYS file on your
computer.
3
Exclude the memory range that the LAN+Modem card
is using.
For example, type this line in the CONFIG.SYS file:
device=c:\windows\emm386.exe NOEMS x=DE00-DFFF
(8k)
where x stands for exclude, followed by an 8K contiguous
block of memory. In this example, the memory setting is
DE00–DFFF.
Refer to the manual that accompanied the memory manager
software for additional instructions and information.
4
Save the CONFIG.SYS file and exit the text editor.
5
Reboot the computer.
Running the Point Enabler Under DOS
For NetWare networking environments, the point enabler
should be installed in the AUTOEXEC.BAT file. Make sure
that the point enabler program, FMENABLE.EXE, is listed
before the ODI driver. The AUTOEXEC.BAT file should
contain the line:
fmenable.exe
For NDIS networking environments, the point enabler
should be installed in the CONFIG.SYS file. Make sure the
that the point enabler program is listed before the NDIS
driver. The CONFIG.SYS file should contain the line:
device=c:\nwclient\fmenable.exe
Alternatively, you can run the configuration manager
manually from DOS each time you use the modem by
typing:
fmenable [Enter]