Home » Canon Manuals » Video Cameras » Canon EOS C300 » Manual Viewer

Canon EOS C300 Instruction Manual - Page 89

Time Code Signal Input, Open the [TC In/Out] submenu., Select [In] and then press SET.

Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

Synchronizing with an External Device Time Code Signal Input An external SMPTE-standard LTC timing signal received from the TIME CODE terminal will be recorded as the time code. The user bit of the external timing signal can also be recorded. Before connecting the device, set the TIME CODE terminal to input. Also, you must set the running mode of the time code to [Free Run] (A 84). Operating modes: 1 Open the [TC In/Out] submenu. [¤ TC/UB Setup] > [Time Code] > [TC In/Out] 2 Select [In] and then press SET. [¤ TC/UB Setup] [Time Code] 89 [TC In/Out] [In] Recording the User Bit of an External Signal The user bit of an external time code signal can also be recorded with the time code itself. [¤ TC/UB Setup] [User Bit] 1 Open the user bit [Rec Mode] submenu. [¤ TC/UB Setup] > [User Bit] > [Rec Mode] 2 Select [External] and then press SET. [Rec Mode] [Internal] NOTES • The Genlock signal synchronization stabilizes after approximately 10 seconds. When the camcorder locks on an external Genlock signal, U will appear on the upper right of the screen. • If the external Genlock signal is incorrect or there is no input signal, the external time code that is recorded may be incorrect. • While a time code signal is being received, the external time code's drop-frame bit will be used (if the external time code is non-drop frame, [NDF] will appear on the rear panel). • When an external time code signal is received, the camcorder's own time code will be synchronized to it and the synchronization will be maintained even if you disconnect the cable from the TIME CODE terminal. However, performing any of the following actions while the cable is not connected will cause the synchronization to be disrupted; the correct time code will be restored once you reconnect the cable. - Turning the camcorder off/on - Changing the operating mode to mode - Changing the video configuration - Changing the frame rate • If the external time code signal is incorrect or there is no input signal, the internal time code set in the [¤ TC/UB Setup] > [Time Code] submenu will be recorded instead. • When the camcorder locks on an external time code signal, [EXT-LOCK] appears on the rear panel.

Section	Page
1. Introduction	11
About this Manual	11
Conventions Used in this Manual	11
Supplied Accessories	13
Names of Parts	14
Monitor Unit	19
Grip Unit	21
Handle Unit	21
2. Preparations	23
Preparing the Power Supply	23
Using a Battery Pack	23
Using a Household Power Outlet	25
Turning the Camcorder On and Off	26
Date, Time and Language Settings	27
Setting the Date and Time	27
Changing the Time Zone	27
Displaying the Date and Time while Recording	28
Changing the Language	28
Using the Menus	29
Selecting an Option from the Menu	29
Using the Customized Submenu (My Menu)	30
Preparing the Camcorder	32
Preparing the Lens	32
Attaching and Removing the Monitor Unit	36
Using the Viewfinder	37
Using the LCD Panel	38
Adjusting the Viewfinder/LCD Screen	39
Using a Tripod	40
Removing and Attaching the Grip Unit	40
Attaching the Handle Unit	41
Attaching a Shoulder Strap	41
Removing and Attaching the Terminal Covers	42
Preparing Recording Media	43
Inserting a CF Card	43
Checking the Status of the CF Card Slots	43
Removing a CF card	44
Inserting and Removing an SD Card	44
Initializing the Recording Media	45
Switching Between the CF Card Slots	45
Selecting the CF Card Recording Method	46
Checking the Available Recording Time for CF Cards	47
Recovering Data on the CF Card	47
Adjusting the Black Balance	48
Remote Operation Via the Wi-Fi Remote Application	49
Preparing the System for Wi-Fi Remote	49
3. Recording	51
Recording Video	51
Preparing to Record	51
Recording	51
Remote Operation Using Wi-Fi Remote	54
Onscreen Displays	55
Rear Panel Displays	57
Canon Log Gamma and CINEMA Preset	58
Video Configuration: Type of Recording, Bit Rate, Resolution and Frame Rate	59
Changing Main Camera Functions with the FUNC. Button	61
Using the Direct Setting Mode	61
Shutter Speed	62
Changing the Shutter Speed Mode and Value	63
Remote Operation Using Wi-Fi Remote	63
Flicker Reduction	64
ISO Speed/Gain	65
Changing the ISO Speed or Gain Value	65
Using the Control Dial	66
Remote Operation Using Wi-Fi Remote	67
ND Filter	68
Using the ND Filter	68
Remote Operation Using Wi-Fi Remote	68
<C300> Adjusting the Aperture	69
Manual Aperture	69
Momentary Automatic Aperture - Push Auto Iris	71
Automatic Aperture	72
Exposure Compensation - AE Shift	72
Light Metering Mode	73
White Balance	74
Setting the White Balance	74
Remote Operation Using Wi-Fi Remote	75
Adjusting the Focus	77
Manual Focus	77
<C300> One-Shot AF	79
<C300> Continuous AF	80
Onscreen Markers and Zebra Patterns	82
Displaying Onscreen Markers	82
Displaying Zebra Patterns	83
Setting the Time Code	84
Selecting the Running Mode	84
Selecting Drop or Non-Drop Frame	85
Putting the Time Code Display on Hold	86
Setting the User Bit	87
Synchronizing with an External Device	88
Connecting an External Device	88
Reference Video Signal Input (Genlock Synchronization)	88
Time Code Signal Input	89
Reference Video Signal Output	90
Time Code Signal Output	90
Recording Audio	91
Connecting an External Microphone or External Audio Input Source to the Camcorder	91
Selecting the Audio Input from the XLR Terminals	92
Adjusting the Audio Level from the XLR Terminals	93
Adjusting the Audio Level from the MIC Terminal	94
Monitoring the Audio with Headphones	95
Selecting the Audio Channel	95
Using Metadata	96
Setting a User Memo Created with Canon XF Utility	96
Setting a User Memo Using Wi-Fi Remote	97
Colors Bars/Audio Reference Signal	98
Recording Color Bars	98
Recording an Audio Reference Signal	98
Video Scopes	99
Displaying a Video Scope	99
Configuring the Waveform Monitor	99
Configuring the Vectorscope	100
Configuring the Edge Monitor	100
Adding Marks while Recording	101
Adding Shot Marks while Recording	101
Remote Operation Using Wi-Fi Remote	101
Adding an OK Mark or Check Mark to the Last Clip Recorded	102
Remote Operation Using Wi-Fi Remote	102
Recording GPS Information (Geotagging)	103
Reviewing a Recording	105
Special Recording Modes	106
Interval Recording Mode	106
Frame Recording Mode	107
Slow & Fast Motion Mode	108
Pre-recording Mode	110
4. Customization	111
Assignable Buttons	111
Changing the Assigned Function	111
Using an Assignable Button	112
Custom Picture Settings	114
Selecting Custom Picture Files	114
Editing a Custom Picture File’s Settings	115
Renaming Custom Picture Files	115
Protecting Custom Picture Files	115
Transferring Custom Picture Files	116
Embedding Custom Picture Settings in a Recording	117
Available Custom Picture Settings	117
Customizing Functions and Onscreen Displays	123
Customizing Functions	123
Customizing Onscreen Displays	123
Saving and Loading Camera Settings	124
Saving Camera Settings to an SD Card	124
Loading Camera Settings from an SD Card	124
5. Playback	125
Playback	125
Clip Index Screen	125
Playing Back Clips	127
Onscreen Displays	128
Playback Controls	129
Adjusting the Volume	129
Clip Operations	130
Using the Clip Menu	131
Displaying Clip Information	131
Adding OK Marks or Check Marks	132
Deleting OK Marks or Check Marks	132
Copying Clips	133
Deleting Clips	134
Deleting the User Memo and GPS Information	134
Copying a Custom Picture File Embedded in a Clip	134
Displaying an Index Screen of Shot Marks	135
Displaying a Frame Index Screen of a Single Clip	136
Adding Shot Marks	136
Deleting Shot Marks	137
Changing a Clip’s Thumbnail	137
6. External Connections	139
Video Output Configuration	139
Video Output Configuration by Terminal	139
Connecting to an External Monitor	140
Connection Diagram	140
Using the HD/SD SDI Terminal	141
Using the HDMI OUT Terminal	141
Using the SYNC OUT Terminal	141
SD Output	142
Superimposing Onscreen Displays to Appear on an External Monitor	142
Saving Clips to a Computer	143
System Requirements	143
Installing and Uninstalling Canon XF Utility (Windows)	144
Installing and Uninstalling Canon XF Utility (Mac OS)	146
Viewing the Software Instruction Manuals	149
7. Photos	151
Taking Photos	151
Taking Photos in CAMERA Mode	151
Capturing Photos in MEDIA Mode	151
Photo Playback	153
Displaying the [Photos] Index Screen	153
Viewing Photos	153
Photo Operations	154
Using the Photo Menu	154
Deleting Photos	154
Protecting Photos	155
Copying Custom Picture Files	156
Photo Numbering	157
8. Additional Information	159
Menu Options	159
Displaying the Status Screens	169
Troubleshooting	176
List of Messages	179
Handling Precautions	182
Maintenance/Others	185
Optional Accessories	187
Specifications	192

Match case Limit results 1 per page

Synchronizing with an External Device

Time Code Signal Input

An external SMPTE-standard LTC timing signal received from the TIME

CODE terminal will be recorded as the time code. The user bit of the

external timing signal can also be recorded. Before connecting the device,

set the TIME CODE terminal to input. Also, you must set the running

mode of the time code to [Free Run] (

84).

1 Open the [TC In/Out] submenu.

[

TC/UB Setup]

[Time Code]

[TC In/Out]

2 Select [In] and then press SET.

Recording the User Bit of an External Signal

The user bit of an external time code signal can also be recorded with the

time code itself.

1 Open the user bit [Rec Mode] submenu.

[

TC/UB Setup]

[User Bit]

[Rec Mode]

Select [External] and then press SET.

NOTES

•

The Genlock signal synchronization stabilizes after approximately 10 seconds. When the camcorder locks on

an external Genlock signal,

will appear on the upper right of the screen.

•

If the external Genlock signal is incorrect or there is no input signal, the external time code that is recorded

may be incorrect.

•

While a time code signal is being received, the external time code’s drop-frame bit will be used (if the external

time code is non-drop frame, [NDF] will appear on the rear panel).

•

When an external time code signal is received, the camcorder’s own time code will be synchronized to it and

the synchronization will be maintained even if you disconnect the cable from the TIME CODE terminal.

However, performing any of the following actions while the cable is not connected will cause the

synchronization to be disrupted; the correct time code will be restored once you reconnect the cable.

Turning the camcorder off/on

Changing the operating mode to

mode

Changing the video configuration

Changing the frame rate

•

If the external time code signal is incorrect or there is no input signal, the internal time code set in the

[

TC/UB Setup]

[Time Code] submenu will be recorded instead.

•

When the camcorder locks on an external time code signal, [EXT-LOCK] appears on the rear panel.

Operating modes:

[

TC/UB Setup]

[Time Code]

[TC In/Out]

[In]

[

TC/UB Setup]

[User Bit]

[Rec Mode]

[Internal]

COPY