D-Link DES-3010G Reference Manual - Page 107

Port Security Commands, config port_security ports

Get D-Link DES-3010G PDF manuals and user guides View all D-Link DES-3010G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 107 highlights

DES-3010F / DES-3010G / DES-3018 / DES-3026 Layer 2 Switch CLI Reference Manual 19 PORT SECURITY COMMANDS The port security commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command config port_security ports show port_security delete port_security_entry vlan_name clear port_security_entry Parameters [ | all ] {admin_state [enable | disable] | max_learning_addr | lock_address_mode [Permanent | DeleteOnTimeout | DeleteOnReset]} {ports } mac_address port port Each command is listed, in detail, in the following sections. NOTE: The uplink module ports (DES-3010F/G ports 9-10, DES-3018 ports 17-18, DES-3026 ports 25-26) do not support the port security function. config port_security ports Purpose Syntax Description Parameters Used to configure port security settings. config port_security ports [ | all ] {admin_state [enable | disable] | max_learning_addr | lock_address_mode [Permanent | DeleteOnTimeout | DeleteOnReset]} This command allows for the configuration of the port security feature. Only the ports listed in the are effected. ports − Specifies a port or range of ports to be configured for port security. all − Configure port security for all ports on the Switch. admin_state [enable | disable] - Enable or disable port security for the listed ports. max_learning_addr - Use this to limit the number of MAC addresses dynamically listed in the FDB for the ports. lock_address_mode [Permanent | DeleteOnTimeout | DeleteOnReset] - Indicates the method of locking addresses. The user has three choices: Permanent - The locked addresses will not age out after the aging timer expires. DeleteOnTimeout - The locked addresses will age out after the aging timer expires. DeleteOnReset - The locked addresses will not age out until the Switch has been reset. 105

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
DES-3010F / DES-3010G / DES-3018 / DES-3026 Layer 2 Switch CLI Reference Manual
19
P
ORT
S
ECURITY
C
OMMANDS
The port security commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the
following table.
Command
Parameters
config port_security ports
[<portlist> | all ] {admin_state [enable | disable] |
max_learning_addr <max_lock_no 0-10> |
lock_address_mode [Permanent | DeleteOnTimeout |
DeleteOnReset]}
show port_security
{ports <portlist>}
delete port_security_entry
vlan_name
<vlan_name 32> mac_address <macaddr> port <port>
clear port_security_entry
port <portlist>
Each command is listed, in detail, in the following sections.
NOTE:
The uplink module ports (DES-3010F/G ports 9-10, DES-3018 ports
17-18, DES-3026 ports 25-26) do not support the port security function.
config port_security ports
Purpose
Used to configure port security settings.
Syntax
config port_security ports [<portlist> | all ] {admin_state
[enable | disable] | max_learning_addr <max_lock_no 0-10> |
lock_address_mode [Permanent | DeleteOnTimeout |
DeleteOnReset]}
Description
This command allows for the configuration of the port security
feature. Only the ports listed in the
<portlist>
are effected.
Parameters
ports <portlist>
−
Specifies a port or range of ports to be
configured for port security.
all
−
Configure port security for all ports on the Switch.
admin_state [enable | disable]
– Enable or disable port security for
the listed ports.
max_learning_addr <max_lock_no 0-10>
- Use this to limit the
number of MAC addresses dynamically listed in the FDB for the
ports.
lock_address_mode [Permanent | DeleteOnTimeout |
DeleteOnReset]
– Indicates the method of locking addresses. The
user has three choices:
±
Permanent
– The locked addresses will not age out after
the aging timer expires.
±
DeleteOnTimeout
– The locked addresses will age out
after the aging timer expires.
±
DeleteOnReset
– The locked addresses will not age out
until the Switch has been reset.
105