D-Link DES-3010G Reference Manual - Page 88

Port Mirroring Commands, config mirror port

Get D-Link DES-3010G PDF manuals and user guides View all D-Link DES-3010G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 88 highlights

DES-3010F / DES-3010G / DES-3018 / DES-3026 Layer 2 Switch CLI Reference Manual 14 PORT MIRRORING COMMANDS The port mirroring commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command config mirror enable mirror disable mirror show mirror Parameters port | [add | delete] source ports [rx | tx | both] Each command is listed, in detail, in the following sections. config mirror port Purpose Used to configure a mirror port − source port pair on the Switch. Syntax config mirror port add source ports [rx | tx | both] Description This command allows a range of ports to have all of their traffic also sent to a designated port, where a network sniffer or other device can monitor the network traffic. In addition, the user can specify that only traffic received by or sent by one or both is mirrored to the Target port. Parameters port − This specifies the Target port (the port where mirrored packets will be sent). add source ports - The port or ports being mirrored. This cannot include the Target port. − This specifies a range of ports that will be mirrored. That is, the range of ports in which all traffic will be copied and sent to the Target port. rx − Allows the mirroring of only packets received by (flowing into) the port or ports in the port list. tx − Allows the mirroring of only packets sent to (flowing out of) the port or ports in the port list. both − Mirrors all the packets received or sent by the port or ports in the port list. Restrictions The Target port cannot be listed as a source port. Only administratorlevel users can issue this command. Example usage: To configure the mirror ports: DES-3026:4# config mirror source port 1 ingress_target port 2 egress_target port 3 Command: config mirror source port 1 ingress_target port 2 egress_target port 3 Success. DES-3026:4# 86

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
DES-3010F / DES-3010G / DES-3018 / DES-3026 Layer 2 Switch CLI Reference Manual
14
P
ORT
M
IRRORING
C
OMMANDS
The port mirroring commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the
following table.
Command
Parameters
config mirror
port <port> | [add | delete] source ports <portlist> [rx | tx | both]
enable mirror
disable mirror
show mirror
Each command is listed, in detail, in the following sections.
config mirror port
Purpose
Used to configure a mirror port
−
source port pair on the Switch.
Syntax
config mirror port <port> add source ports <portlist> [rx | tx | both]
Description
This command allows a range of ports to have all of their traffic also
sent to a designated port, where a network sniffer or other device can
monitor the network traffic. In addition, the user can specify that only
traffic received by or sent by one or both is mirrored to the Target port.
Parameters
port <port>
−
This specifies the Target port (the port where mirrored
packets will be sent).
add source ports
– The port or ports being mirrored. This cannot include
the Target port.
±
<portlist>
−
This specifies a range of ports that will be mirrored.
That is, the range of ports in which all traffic will be copied and sent
to the Target port.
rx
−
Allows the mirroring of only packets
received by (flowing into) the port or ports in the port list.
tx
−
Allows the mirroring of only packets sent to (flowing out of) the port
or ports in the port list.
both
−
Mirrors all the packets received or sent by the port or ports in the
port list.
Restrictions
The Target port cannot be listed as a source port. Only administrator-
level users can issue this command.
Example usage:
To configure the mirror ports:
DES-3026:4# config mirror source port 1 ingress_target port 2
egress_target port 3
Command: config mirror source port 1 ingress_target port 2 egress_target
port 3
Success.
DES-3026:4#
86