D-Link DES-3010G Reference Manual - Page 59

config syslog host, Warning: warning conditions, Informational: informational messages

Get D-Link DES-3010G PDF manuals and user guides View all D-Link DES-3010G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

DES-3010F / DES-3010G / DES-3018 / DES-3026 Layer 2 Switch CLI Reference Manual config syslog host protocol to send system log information to a remote host. Parameters all − Specifies that the command will be applied to all hosts. − Specifies that the command will be applied to an index of hosts. There are four available indexes, numbered 1 through 4. severity − Severity level indicator. These are described in the following: Bold font indicates that the corresponding severity level is currently supported on the Switch. Numerical Severity Code 0 Emergency: system is unusable 1 Alert: action must be taken immediately 2 Critical: critical conditions 3 Error: error conditions 4 Warning: warning conditions 5 Notice: normal but significant condition 6 Informational: informational messages 7 Debug: debug-level messages informational − Specifies that informational messages will be sent to the remote host. This corresponds to number 6 from the list above. warning − Specifies that warning messages will be sent to the remote host. This corresponds to number 4 from the list above. all − Specifies that all of the currently supported syslog messages that are generated by the Switch will be sent to the remote host. facility − Some of the operating system daemons and processes have been assigned Facility values. Processes and daemons that have not been explicitly assigned a Facility may use any of the "local use" facilities or they may use the "user-level" Facility. Those Facilities that have been designated are shown in the following: Bold font indicates the facility values the Switch currently supports. Numerical Facility Code 0 kernel messages 1 user-level messages 2 mail system 3 system daemons 4 security/authorization messages 5 messages generated internally by syslog 6 line printer subsystem 7 network news subsystem 8 UUCP subsystem 9 clock daemon 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
DES-3010F / DES-3010G / DES-3018 / DES-3026 Layer 2 Switch CLI Reference Manual
config syslog host
protocol to send system log information to a remote host.
Parameters
all
−
Specifies that the command will be applied to all hosts.
<index 1-4>
−
Specifies that the command will be applied to an index
of hosts. There are four available indexes, numbered 1 through 4.
severity
−
Severity level indicator. These are described in the
following:
Bold
font indicates that the corresponding severity level is currently
supported on the Switch.
Numerical
Severity
Code
0
Emergency: system is unusable
1
Alert: action must be taken immediately
2
Critical: critical conditions
3
Error: error conditions
4
Warning: warning conditions
5
Notice: normal but significant condition
6
Informational: informational messages
7
Debug: debug-level messages
informational
−
Specifies that informational messages will be sent to
the remote host. This corresponds to number 6 from the list above.
warning
−
Specifies that warning messages will be sent to the
remote host. This corresponds to number 4 from the list above.
all
−
Specifies that all of the currently supported syslog messages
that are generated by the Switch will be sent to the remote host.
facility
−
Some of the operating system daemons and processes
have been assigned Facility values. Processes and daemons that
have not been explicitly assigned a Facility may use any of the "local
use" facilities or they may use the "user-level" Facility. Those
Facilities that have been designated are shown in the following:
Bold
font indicates the facility values the Switch currently supports.
Numerical
Facility
Code
0
kernel messages
1
user-level messages
2
mail system
3
system daemons
4
security/authorization messages
5
messages generated internally by syslog
6
line printer subsystem
7
network news subsystem
8
UUCP subsystem
9
clock daemon
57