D-Link DES-3010G Reference Manual - Page 114

Backend State: Request/Response/Fail/Idle/Initialize, Port Control: ForceAuth/ForceUnauth/Auto

Get D-Link DES-3010G PDF manuals and user guides View all D-Link DES-3010G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 114 highlights

DES-3010F / DES-3010G / DES-3018 / DES-3026 Layer 2 Switch CLI Reference Manual show 802.1x auth_configuration authenticated, and can not access the network. PAE State: Initialize/Disconnected/Connecting/ Authenticating/Authenticated/Held /ForceAuth/ForceUnauth − Shows the current state of the Authenticator PAE. Backend State: Request/Response/Fail/Idle/Initialize − Shows the current state of the Backend Authenticator. AdminCtlDir: Both/In − Shows whether a controlled Port that is unauthorized will exert control over communication in both receiving and transmitting directions, or just the receiving direction. OpenCtlDir: Both/In − Shows whether a controlled Port that is unauthorized will exert control over communication in both receiving and transmitting directions, or just the receiving direction. Port Control: ForceAuth/ForceUnauth/Auto − Shows the administrative control over the port's authorization status. ForceAuth forces the Authenticator of the port to become Authorized. ForceUnauth forces the port to become Unauthorized. QuietPeriod − Shows the time interval between authentication failure and the start of a new authentication attempt. TxPeriod − Shows the time to wait for a response from a supplicant (user) to send EAP Request/Identity packets. SuppTimeout − Shows the time to wait for a response from a supplicant (user) for all EAP packets, except for the Request/Identity packets. ServerTimeout − Shows the length of time to wait for a response from a RADIUS server. MaxReq − Shows the maximum number of times to retry sending packets to the supplicant. ReAuthPeriod − Shows the time interval between successive reauthentications. ReAuthenticate: Enabled/Disabled − Shows whether or not to reauthenticate. Parameters ports − Specifies a port or range of ports to be viewed. Restrictions Only administrator-level users can issue this command. Example usage: To display the 802.1x configurations: 112

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
DES-3010F / DES-3010G / DES-3018 / DES-3026 Layer 2 Switch CLI Reference Manual
show 802.1x
auth_configuration
authenticated, and can not access the network.
PAE State: Initialize/Disconnected/Connecting/
Authenticating/Authenticated/Held /ForceAuth/ForceUnauth
−
Shows the
current state of the Authenticator PAE.
Backend State: Request/Response/Fail/Idle/Initialize
−
Shows the current
state of the Backend Authenticator.
AdminCtlDir: Both/In
−
Shows whether a controlled Port that is unauthorized
will exert control over communication in both receiving and transmitting
directions, or just the receiving direction.
OpenCtlDir: Both/In
−
Shows whether a controlled Port that is unauthorized
will exert control over communication in both receiving and transmitting
directions, or just the receiving direction.
Port Control: ForceAuth/ForceUnauth/Auto
−
Shows the administrative
control over the port’s authorization status. ForceAuth forces the
Authenticator of the port to become Authorized. ForceUnauth forces the
port to become Unauthorized.
QuietPeriod
−
Shows the time interval between authentication failure and
the start of a new authentication attempt.
TxPeriod
−
Shows the time to wait for a response from a supplicant (user)
to send EAP Request/Identity packets.
SuppTimeout
−
Shows the time to wait for a response from a supplicant
(user) for all EAP packets, except for the Request/Identity packets.
ServerTimeout
−
Shows the length of time to wait for a response from a
RADIUS server.
MaxReq
−
Shows the maximum number of times to retry sending packets to
the supplicant.
ReAuthPeriod
−
Shows the time interval between successive re-
authentications.
ReAuthenticate: Enabled/Disabled
−
Shows whether or not to re-
authenticate.
Parameters
ports <portlist>
−
Specifies a port or range of ports to be viewed.
Restrictions
Only administrator-level users can issue this command.
Example usage:
To display the 802.1x configurations:
112