D-Link DSR-1000AC User Manual - Page 322

Appendix D - Log Output Reference Pattern added already Error : All the %d pattern are in use. Cannot add a new pattern , MAX_NUM_PATTERN Pattern added to entry %d ,i Remove wake up pattern mask = %p pat = %p ,maskBytes,patternBytes DEBUG DEBUG DEBUG DEBUG DEBUG mask = %x pat = %x ,(u_int32_t)maskBytes, (u_int32_t)patternBytes Pattern Removed from entry %d ,i Error : Pattern not found DEBUG DEBUG DEBUG PPM STATE ILLEGAL %x %x, forcePpmStateCur, afp->forceState DEBUG FORCE_PPM %4d %6.6x %8.8x %8.8x %8.8x %3.3x %4.4x, failed to allocate tx descriptors: %d, error failed to allocate beacon descripotrs: %d, error failed to allocate UAPSD descripotrs: %d, error hal qnum %u out of range, max %u!, HAL AC %u out of range, max %zu!, HAL AC %u out of range, max %zu!, %s: unable to update hardware queue %u!, DEBUG DEBUG DEBUG DEBUG DEBUG DEBUG DEBUG DEBUG Multicast Q: %p , buf buf flags - 0x%08x buf->bf_flags buf status - 0x%08x, buf->bf_status # frames in aggr - %d, length of aggregate - %d, length of frame - %d, sequence number - %d, tidno - %d, DEBUG DEBUG DEBUG DEBUG DEBUG isdata: %d isaggr: %d isampdu: %d ht: %d isretried: %d isxretried: %d shpreamble: %d isbar: %d ispspoll: %d aggrburst: %d calcairtime: %d qosnulleosp: %d, DEBUG %p: 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x, DEBUG 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x, DEBUG 0x%08x 0x%08x 0x%08x 0x%08x, DEBUG sc_txq[%d] : , i tid %p pause %d : , tid, tid->paused %d: %p , j, tid->tx_buf[j] %p , buf axq_q: DEBUG DEBUG DEBUG DEBUG DEBUG ERROR: %s: Timeout at page %#0x addr %#0x Invalid IOCTL %#08x, cmd %s: unable to register device, dev>name ath_pci: 32-bit DMA not available ath_pci: cannot reserve PCI memory region ath_pci: cannot remap PCI memory region) ; ERROR ERROR ERROR ERROR ERROR ERROR ath_pci: no memory for device state %s: unable to register device, dev>name ERROR ERROR ath_dev_probe: no memory for device state ERROR %s: no memory for device state, __func__ kernel MIBCTL registration failed! Bad ioctl command WpsMod: Failed to configure gpio pin WpsMod: Failed to register interrupt handler registering char device failed unregistering char device failed %s:%d - ERROR: non-NULL node pointer in %p, %p! %s:%d - ERROR: non-NULL node pointer in %p, %p! can't alloc name %s, name %s: unable to register device, dev>name failed to automatically load module: %s; \ Unable to load needed module: %s; no support for \ ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR ERROR Module \%s\ is not known, buf ERROR Error loading module \%s\, buf ERROR Module \%s\ failed to initialize, buf ERROR ath_pci: 32-bit DMA not available ath_pci: cannot reserve PCI memory region ath_pci: cannot remap PCI memory region) ; ath_pci: no memory for device state %s: unable to attach hardware: '%s' (HAL status %u), %s: HAL ABI mismatch; ERROR ERROR ERROR ERROR ERROR ERROR D-Link DSR-Series User Manual 309