Dell IP4700 Service Guide - Page 67

Precautions When Removing, Installing, or Storing CRUs

Get Dell IP4700 PDF manuals and user guides View all Dell IP4700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Servicing and Upgrading an IP4700 3 IMPORTANT: These procedures are not a substitute for the use of an ESD kit. Follow them only in the event of an emergency. • Before touching any CRU, touch a bare (unpainted) metal surface of the enclosure. • Before removing any CRU from its antistatic bag, place one hand firmly on a bare metal surface of the enclosure, and at the same time, pick up the CRU while it is still sealed in the antistatic bag. Once you have done this, do not move around the room or contact other furnishings, personnel, or surfaces until you have installed the CRU. • Remove the CRU from the antistatic bag. Avoid touching any electronic components and circuits on it. • If you must move around the room or touch other surfaces before installing a CRU, first place the CRU back in the antistatic bag. When you are ready again to install the CRU, repeat these procedures. Precautions When Removing, Installing, or Storing CRUs Use the precautions listed below when you remove, handle, or store CRUs. • Do not remove a faulty CRU until you have a replacement available. • Handle a CRU only when using an ESD wristband as follows: Attach the clip of the ESD wristband to the ESD bracket or bare metal on the IP4700 enclosure, and put the wristband around your wrist with the metal button against your skin. • Handle CRUs gently. A sudden jar, drop, or vibration can permanently damage a CRU. • Never use excessive force to remove or install a CRU. • Store a CRU in the antistatic bag and specially designed shipping container in which you received it. Use that container if you need to return the CRU for repair. • Maintain the location where you store CRUs within the limits specified in Appendix A. Handling CRUs 3-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
3
Handling CRUs
3-7
Servicing and Upgrading an IP4700
IMPORTANT:
These procedures are not a substitute for the use of an ESD
kit. Follow them only in the event of an emergency.
•
Before touching any CRU, touch a bare (unpainted) metal surface
of the enclosure.
•
Before removing any CRU from its antistatic bag, place one hand
firmly on a bare metal surface of the enclosure, and at the same
time, pick up the CRU while it is still sealed in the antistatic bag.
Once you have done this, do not move around the room or
contact other furnishings, personnel, or surfaces until you have
installed the CRU.
•
Remove the CRU from the antistatic bag. Avoid touching any
electronic components and circuits on it.
•
If you must move around the room or touch other surfaces before
installing a CRU, first place the CRU back in the antistatic bag.
When you are ready again to install the CRU, repeat these
procedures.
Precautions When Removing, Installing, or Storing CRUs
Use the precautions listed below when you remove, handle, or store
CRUs.
•
Do not remove a faulty CRU until you have a replacement
available.
•
Handle a CRU only when using an ESD wristband as follows:
Attach the clip of the ESD wristband to the ESD bracket or bare
metal on the IP4700 enclosure, and put the wristband around
your wrist with the metal button against your skin.
•
Handle CRUs gently. A sudden jar, drop, or vibration can
permanently damage a CRU.
•
Never use excessive force to remove or install a CRU.
•
Store a CRU in the antistatic bag and specially designed shipping
container in which you received it. Use that container if you need
to return the CRU for repair.
•
Maintain the location where you store CRUs within the limits
specified in Appendix A.