Dell Latitude CP Replacement Instructions - Page 44

Modular Bay Devices (Diskette Drive, CD-ROM Drive, Battery, or Travel Module), Audio Shield

Get Dell Latitude CP PDF manuals and user guides View all Dell Latitude CP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

latch lock NOTE: You do not need to remove the main battery or hard-disk drive prior to this procedure. 1. Close the display and turn the computer over. 2. Remove the device from the modular bay. Push the modular bay latch away from the center of the computer. Keep holding the latch open while pulling the device out of the modular bay with the other hand. 1. Remove the palmrest assembly. 2. Remove the 5-mm screw securing the audio board shield (see Figure 26). 3. Remove the audio board shield. NOTE: When replacing the audio shield, ensure that the audio shield is properly seated to prevent it from cutting into the speaker wires or interfering with devices installed in the modular bay. (You can check this by temporarily installing a device in the modular bay prior to reinstalling the palmrest assembly.) 38 Dell Latitude CP and CPi - Parts Removal and Replacement Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
38
Dell Latitude CP and CPi
—
Parts Removal and Replacement Guide
ÂôÄÀ²³ºÇ²Áº¶¼»·È¼¸º%¶·¸¹¼Êʼº¶³·»¼&º
Ŷµ'(º¶³·»¼&ºÇ²Êʼ³Á&ºÃ³ºË³²»¼ÀºÂôÄÀ¼)ººººººº
±²³´µ¶·Â'¹··Ã»!´ÉÁµ·ÄÁÅ·$¶Ë²Î¶·Ê¶¼»ËÁÉ···
NOTE: You do not need to remove the main battery or hard-disk drive prior to
this procedure.
±²³´µ¶·¸ &½'¿ ÀË¿ ¾Á¿ ÈÄÂ' ÀËÂɽ¼¿ ¹À ¼Å¿½º ¾Ä ÿ̿º¾ À¼Â½¾¼Á¹ºÇ
¾Á¿ ¼ÄÆÃ˾¿Â ¼ÄÌ¿ÂÎ
1.
Close the display and turn the computer over.
2.
Remove the device from the modular bay.
Push the modular bay latch away from the center of the computer. Keep
holding the latch open while pulling the device out of the modular bay with
the other hand.
½Ä´·Ãº*Ì·¼À´
²
1.
Remove the palmrest assembly.
2.
Remove the 5-mm screw securing the audio board shield (see
Figure 26).
3.
Remove the audio board shield.
NOTE: When replacing the audio shield, ensure that the audio shield is
properly seated to prevent it from cutting into the speaker wires or interfering
with devices installed in the modular bay. (You can check this by temporarily
installing a device in the modular bay prior to reinstalling the palmrest
assembly.)
latch lock