Dell Latitude CP Replacement Instructions - Page 47

Module Latch Assemblies, Ensure that the newly installed latch moves smoothly and freely

Get Dell Latitude CP PDF manuals and user guides View all Dell Latitude CP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

module latch assemblies (2) springs (2) module latches (2) 1. Remove the bottom case bracket. 2. Remove the left latch from the outside of the bottom case by unsnapping the slider-spring assembly. Keep pressure applied to the slider-spring assembly while unsnapping the latch to prevent the slider-spring assembly from coming loose from the case. If the slider-spring assembly does come loose from the case: a. Carefully reinsert the spring onto the plunger on the slider, and reinstall the slider-spring assembly into the holding features on the inside of the case. b. Ensure that the plunger is inserted in its respective hole, that the side of the slider with the two bumps is facing the rear of the case, and that the surface with the wear ribs is facing the bottom of the case (see Figure 29). 3. Snap in the new latch from the bottom of the base, making certain its snap features are fully engaged in the slider. 4. Ensure that the newly installed latch moves smoothly and freely when pushed and released. Dell Latitude CP and CPi - Parts Removal and Replacement Guide 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
Dell Latitude CP and CPi
—
Parts Removal and Replacement Guide
41
ÂôÄÀ¼º#²ÊÈ̺½¸¸¼¾¿À·¼¸
±²³´µ¶·Â1¹··Ã»!´É¶·9Á¾Î5·ÆÇǶ¼Èɲ¶Ç·Ê¶¼»ËÁÉ
1.
Remove the bottom case bracket.
2.
Remove the left latch from the outside of the bottom case by
unsnapping the slider-spring assembly.
Keep pressure applied to the slider-spring assembly while unsnapping the
latch to prevent the slider-spring assembly from coming loose from the
case. If the slider-spring assembly does come loose from the case:
a.
Carefully reinsert the spring onto the plunger on the slider, and
reinstall the slider-spring assembly into the holding features on the
inside of the case.
b.
Ensure that the plunger is inserted in its respective hole, that the side
of the slider with the two bumps is facing the rear of the case, and
that the surface with the wear ribs is facing the bottom of the case
(see Figure 29).
3.
Snap in the new latch from the bottom of the base, making certain
its snap features are fully engaged in the slider.
4.
Ensure that the newly installed latch moves smoothly and freely
when pushed and released.
module latch
assemblies (2)
springs (2)
module latches (2)