Dell Latitude CP Replacement Instructions - Page 55

Reserve Battery, Disconnect the reserve battery cable from connector JBAT1 on

Get Dell Latitude CP PDF manuals and user guides View all Dell Latitude CP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

reserve battery reserve battery cable connector (JBAT1) To remove the reserve battery, follow these steps: 1. Remove the palmrest assembly. 2. Disconnect the reserve battery cable from connector JBAT1 on the system board. 3. Remove the reserve battery from the bottom case bracket. a. Tear the reserve battery free from the foam pad. b. Remove the remnants of the foam pad from the system board assembly. NOTE: When replacing the reserve battery, first connect the reserve battery cable to the system board. Then position the reserve battery on the hard-disk drive bay so there is minimal slack in the cable. Dell Latitude CP and CPi - Parts Removal and Replacement Guide 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
Dell Latitude CP and CPi
—
Parts Removal and Replacement Guide
49
'¼¸¼³»¼ºÇ²Êʼ³Áººº
±²³´µ¶·Ì'¹··Ê¶Ç¶µË¶·ÄÁ¾¾¶µÅ·°ÀǾÁÉÉÁ¾²»À·······
±²³´µ¶·¸ ´Á¿ ¿À¿ÂÌ¿ ͽ¾¾¿ÂÊ ÃÂÄ̹»¿À ÃÄÈ¿Â ¾Ä ¾Á¿ ¼ÄÆÃ˾¿Â8À !´±
½º» ·9!²& ÈÁ¿º ¾Á¿ ¼ÄÆÃ˾¿Â ¹À ¾Ëº¿» ÄÉÉÎ !¿ÆÄ̹ºÇ ¾Á¿ ͽ¾¾¿ÂÊ
¼½ËÀ¿À ¾Á¿ ¼ÄÆÃ˾¿Â ¾Ä ÅÄÀ¿ ¹¾À »½¾¿ ½º» ¾¹Æ¿ ¹ºÉÄÂƽ¾¹Äº ½À È¿ÅÅ ½À
½ÅÅ ËÀ¿Â)À¿¾¾½ÍÅ¿ ý½ƿ¾¿ÂÀ ¹º ·9!²&Î µÉ ÃÄÀÀ¹ÍÅ¿% ƽ'¿ ½ ¼ÄÃÊ ÄÉ
¾Á¹À ¹ºÉÄÂƽ¾¹Äº Í¿ÉÄ¿ ÊÄË Â¿ÆÄÌ¿ ¾Á¿ ¿À¿ÂÌ¿ ͽ¾¾¿ÂÊÎ
To remove the reserve battery, follow these steps:
1.
Remove the palmrest assembly.
2.
Disconnect the reserve battery cable from connector JBAT1 on the
system board.
3.
Remove the reserve battery from the bottom case bracket.
a.
Tear the reserve battery free from the foam pad.
b.
Remove the remnants of the foam pad from the system board
assembly.
NOTE: When replacing the reserve battery, first connect the reserve battery
cable to the system board. Then position the reserve battery on the hard-disk
drive bay so there is minimal slack in the cable.
reserve battery
reserve battery cable
connector (JBAT1)