Dell PowerEdge 4300 Dell PowerEdge 4300 Systems Service Manual - Page 47

Huuru, Idloxuh, Uhdoorfdwhg

Get Dell PowerEdge 4300 PDF manuals and user guides View all Dell PowerEdge 4300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Embedded server management memory may be temporarily corrupted Shut down the system to clear the memory, and then restart the system. If the problem persists, disconnect all power cables from the system for at least one minute; then try again. Faulty keyboard controller (defective system board) Corrupted or improperly installed operating system Incorrect configuration settings in System Setup program, improperly connected hard-disk drive, faulty harddisk drive controller subsystem (defective system board), or loose power cable Incorrect ISA_CLR jumper configuration, incorrect configuration settings in System Setup program, or faulty battery Incorrect microprocessor jumper configuration Replace the system board. Reinstall the operating system. Check the primary and secondary SCSI configuration settings in the System Setup program. Reinstall the hard-disk drive. Check the interface cable and power cable connections to the backplane board. If the problem still persists, replace the system board. Remove the plug from the ISA_CLR jumper. Check the System Setup configuration settings. Replace the battery. Check the microprocessor speed jumper. Resource conflict detected and corrected when system resources were allocated using the RCU No action is required. Codes and Messages 3-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Codes and Messages
3-7
(PEHGGHG±
VHUYHU±
PDQDJHPHQW±
HUURU
(PEHGGHG±
VHUYHU±
PDQDJHPHQW±LV±
QRW±SUHVHQW
Embedded server
management
memory may be
temporarily
corrupted
Shut down the system to
clear the memory, and
then restart the system.
If the problem persists,
disconnect all power
cables from the system
for at least one minute;
then try again.
*DWH±$¸¶±
IDLOXUH
Faulty keyboard
controller (defective
system board)
Replace the system
board.
*HQHUDO±
IDLOXUH
Corrupted or
improperly installed
operating system
Reinstall the operating
system.
+DUG±GLVN±
GULYH±UHDG±
IDLOXUH
+DUG±GLVN±
IDLOXUH
Incorrect configura-
tion settings in
System Setup pro-
gram, improperly
connected hard-disk
drive, faulty hard-
disk drive controller
subsystem (defec-
tive system board),
or loose power
cable
Check the primary and
secondary SCSI
configuration settings in
the System Setup
program. Reinstall the
hard-disk drive. Check
the interface cable and
power cable connections
to the backplane board.
If
the problem still persists,
replace the system
board.
,QYDOLG±
FRQILJXUDWLRQ±
LQIRUPDWLRQ±³±
SOHDVH±UXQ±
6(783±SURJUDP
Incorrect ISA_CLR
jumper configura-
tion, incorrect
configuration set-
tings in System
Setup program, or
faulty battery
Remove the plug from
the ISA_CLR jumper.
Check the System Setup
configuration settings.
Replace the battery.
,QYDOLG±&38±
VSHHG±
GHWHFWHG±³±
FKHFN±MXPSHUV
Incorrect micro-
processor jumper
configuration
Check the microproces-
sor speed jumper.
,QYDOLG±195$0±
FRQILJXUD³
WLRQ¹±
UHVRXUFH±
UHDOORFDWHG
Resource conflict
detected and
corrected when sys-
tem resources were
allocated using the
RCU
No action is required.
7DEOH±¶´µ³±6\VWHP±0HVVDJHV
±²FRQWLQXHG³
0HVVDJH
&DXVH
&RUUHFWLYH²$FWLRQ