Dell PowerEdge 4300 Dell PowerEdge 4300 Systems Service Manual - Page 63

NOTE: The ribbon cable that attaches to the control panel assembly connects

Get Dell PowerEdge 4300 PDF manuals and user guides View all Dell PowerEdge 4300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

ribbon cable control panel thumbscrew To remove the control panel assembly, follow these steps: 1. Disconnect the ribbon cable from its connector on the left side of the con- trol panel assembly (see Figure 4-3). 2. Loosen the thumbscrew securing the control panel assembly to the front of the chassis. 3. Slide the control panel assembly to the right (or up if system is in rack- mount position) to disengage the assembly from the chassis hooks. NOTE: The ribbon cable that attaches to the control panel assembly connects to the PLANAR connector on the SCSI backplane and then continues on to the BACKPLANE connector on the system board. Removing and Replacing Parts 4-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Removing and Replacing Parts
4-5
&RQWURO±3DQHO±$VVHPEO\
)LJXUH±·´¶³±±&RQWURO´3DQHO±$VVHPEO\±5HPRYDO
To remove the control panel assembly, follow these steps:
1.
Disconnect the ribbon cable from its connector on the left side of the con-
trol panel assembly (see Figure 4-3).
2.
Loosen the thumbscrew securing the control panel assembly to the front
of the chassis.
3.
Slide the control panel assembly to the right (or up if system is in rack-
mount position) to disengage the assembly from the chassis hooks.
NOTE: The ribbon cable that attaches to the control panel assembly connects
to the PLANAR connector on the SCSI backplane and then continues on to the
BACKPLANE connector on the system board.
ribbon cable
thumbscrew
control panel