Dell PowerEdge 4300 Dell PowerEdge 4300 Systems Service Manual - Page 74

almost

Get Dell PowerEdge 4300 PDF manuals and user guides View all Dell PowerEdge 4300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

cutouts (2) legs (2) handle locking bar latch To remove a power supply, follow these steps: 1. Disconnect the AC power cable from the electrical outlet, and then dis- connect the other end of the cable from the power supply. 2. Press the locking bar in the power supply handle to the left (or up if the sys- tem is in the rack-mount position) until the latch disengages from the chassis (see Figure 4-11). 3. Rotate the handle outward (forcing the power supply partially out of its bay) and pull the power supply the rest of the way out by the handle. When installing a power supply, make sure the handle is all the way out (at a right angle to the back of the power supply). Slide the power supply almost all the way into its bay, letting it extend out about a quarter of an inch. Rotate the handle back toward the power supply while fitting the two legs of the handle into the cutouts in the chassis wall and, at the same time, pressing the power supply the rest of the way into the bay. Then push the locking bar to the right (or down if the system is in the rack-mount position) until the latch snaps into place, securing the power supply. 4-16 Dell PowerEdge 4300 Systems Service Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
4-16
Dell PowerEdge 4300 Systems Service Manual
6\VWHP±3RZHU±6XSSO\
)LJXUH±·´²²³±±3RZHU±6XSSO\±5HPRYDO
:$51,1*±²)RU²V\VWHPV²ZLWK²QRQUHGXQGDQW²SRZHU²VXSSOLHV·²WXUQ²RII²
SRZHU²WR²WKH²V\VWHP²EHIRUH²UHPRYLQJ²WKH²V\VWHP²SRZHU²VXSSOLHV³
To remove a power supply, follow these steps:
1.
Disconnect the AC power cable from the electrical outlet, and then dis-
connect the other end of the cable from the power supply.
2.
Press the locking bar in the power supply handle to the left (or up if the sys-
tem is in the rack-mount position) until the latch disengages from the
chassis (see Figure 4-11).
3.
Rotate the handle outward (forcing the power supply partially out of its bay)
and pull the power supply the rest of the way out by the handle.
When installing a power supply, make sure the handle is all the way out (at a
right angle to the back of the power supply). Slide the power supply
almost
all
the way into its bay, letting it extend out about a quarter of an inch. Rotate the
handle back toward the power supply while fitting the two legs of the handle
into the cutouts in the chassis wall and, at the same time, pressing the power
supply the rest of the way into the bay. Then push the locking bar to the right
(or down if the system is in the rack-mount position) until the latch snaps into
place, securing the power supply.
&$87,21±²7KH²SRZHU²VXSSO\²ZLOO²QRW²RSHUDWH²XQOHVV²WKH²KDQGOH²LV²
VQDSSHG²DOO²WKH²ZD\²LQWR²WKH²ORFNHG²SRVLWLRQ³
cutouts (2)
handle
locking bar
latch
legs (2)