Dell PowerEdge C4140 EMC Installation and Service Manual - Page 121

Installing SXM2 GPU

Get Dell PowerEdge C4140 PDF manuals and user guides View all Dell PowerEdge C4140 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 121 highlights

Figure 93. Installing SXM2 GPU Next steps 1. Install the SXM2-GPU heat sink. 2. Install the NVLink air shroud. Installing the SXM2-GPU Heat Sink Prerequisites 1. Follow the safety guidelines listed in the Safety instructions section. 2. Follow the procedure listed in Before working inside your system. Steps 1. If you are using an existing SXM2-GPU heat sink, remove the thermal grease from the heat sink by using a clean lint-free cloth. 2. Using the thermal grease syringe included with your processor kit apply the grease in a thin spiral on the top of the processor. CAUTION: Applying too much thermal grease can result in excess grease coming in contact with and contaminating the processor socket. NOTE: The thermal grease syringe is intended for one-time use only. Dispose the syringe after you use it. 3. Align the screws on the heat sink with the standoffs on the system board. PowerEdge C4140 installing and removing system components 121

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
Figure 93. Installing SXM2 GPU
Next steps
1.
Install the SXM2-GPU heat sink
.
2.
Install the NVLink air shroud
.
Installing the SXM2-GPU Heat Sink
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
section.
2.
Follow the procedure listed in
Before working inside your system
.
Steps
1.
If you are using an existing SXM2-GPU heat sink, remove the thermal grease from the heat sink by using a clean lint-free cloth.
2.
Using the thermal grease syringe included with your processor kit apply the grease in a thin spiral on the top of the processor.
CAUTION:
Applying too much thermal grease can result in excess grease coming in contact with and contaminating
the processor socket.
NOTE:
The thermal grease syringe is intended for one-time use only. Dispose the syringe after you use it.
3.
Align the screws on the heat sink with the standoffs on the system board.
PowerEdge C4140 installing and removing system components
121