Dell PowerEdge C4140 EMC Installation and Service Manual - Page 67

Hard drives, Removing the 2.5-inch drive cage

Get Dell PowerEdge C4140 PDF manuals and user guides View all Dell PowerEdge C4140 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Figure 33. Installing a cooling fan Next steps 1. Install the air shroud.. 2. Follow the procedure listed in After working inside your system on page 58. Hard drives Removing the 2.5-inch drive cage Prerequisites 1. Follow the safety guidelines listed in the Safety instructions section. 2. Follow the procedure listed in Before working inside your system. 3. Disconnect the power and signal cable from the system board. 4. Keep the Phillips #1 screwdriver ready. Steps 1. Disconnect the cables from the system board. 2. Remove the screw securing the drive cage to the chassis. 3. Slide the drive cage out of the drive cage slot. PowerEdge C4140 installing and removing system components 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
Figure 33. Installing a cooling fan
Next steps
1.
Install the air shroud.
.
2.
Follow the procedure listed in
After working inside your system
on page 58.
Hard drives
Removing the 2.5-inch drive cage
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
section.
2.
Follow the procedure listed in
Before working inside your system
.
3.
Disconnect the power and signal cable from the system board.
4.
Keep the Phillips #1 screwdriver ready.
Steps
1.
Disconnect the cables from the system board.
2.
Remove the screw securing the drive cage to the chassis.
3.
Slide the drive cage out of the drive cage slot.
PowerEdge C4140 installing and removing system components
67