Dell PowerEdge C4140 EMC Installation and Service Manual - Page 39
Option, Description, x2APIC Mode
![]() |
View all Dell PowerEdge C4140 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 39 highlights
Option Description NOTE: The standard and basic bin processors support lower link frequencies. The options available are Maximum data rate, 10.4 GT/s, and 9.6 GT/s. This option is set to Maximum data rate by default. Maximum data rate indicates that the BIOS runs the communication links at the maximum frequency that is supported by the processors. You can also select specific frequencies that the processors support, which can vary. For best performance, you should select Maximum data rate. Any reduction in the communication link frequency affects the performance of non-local memory accesses and cache coherency traffic. Besides, it can slow access to non-local I/O devices from a particular processor. However, if power-saving considerations outweigh performance, you might want to reduce the frequency of the processor communication links. If you do this, you should localize memory and I/O accesses to the nearest NUMA node to minimize the impact to system performance. Virtualization Technology Enables or disables the virtualization technology for the processor. This option is set to Enabled by default. Adjacent Cache Line Prefetch Optimizes the system for applications that need high utilization of sequential memory access. This option is set to Enabled by default. You can disable this option for applications that need high utilization of random memory access. Hardware Prefetcher Enables or disables the hardware prefetcher. This option is set to Enabled by default. Software Prefetcher Enables or disables the software prefetcher. This option is set to Enabled by default. DCU Streamer Prefetcher Enables or disables the Data Cache Unit (DCU) streamer prefetcher. This option is set to Enabled by default. DCU IP Prefetcher Enables or disables the Data Cache Unit (DCU) IP prefetcher. This option is set to Enabled by default. Sub NUMA Cluster Sub NUMA Clustering (SNC) is a feature for breaking up the LLC into disjoint clusters based on address range, with each cluster bound to a subset of the memory controllers in the system. It improves average latency to the LLC. Enables or disables the Sub NUMA Cluster. This option is set to Disabled by default. UPI Prefetch Enables you to get the memory that is read started early on DDR bus. The Ultra Path Interconnect (UPI) Rx path will spawn the speculative memory that is read to Integrated Memory Controller (iMC) directly. This option is set to Enabled by default. LLC Prefetch Enables or disables the LLC Prefetch on all threads. This option is set to Disabled by default. Dead Line LLC Alloc Enables or disables the Dead Line LLC Alloc. This option is set to Enabled by default. You can enable this option to enter the dead lines in LLC or disable the option to not enter the dead lines in LLC. Directory AtoS Enables or disables the Directory AtoS. AtoS optimization reduces remote read latencies for repeat read accesses without intervening writes. This option is set to Disabled by default. Logical Processor Idling Enables you to improve the energy efficiency of a system. It uses the operating system core parking algorithm and parks some of the logical processors in the system which in turn allows the corresponding processor cores to transition into a lower power idle state. This option can only be enabled if the operating system supports it. It is set to Disabled by default. Configurable TDP Enables you to configure the TDP level. The available options are Nominal, Level 1, and Level 2. This option is set to Nominal by default. NOTE: This option is only available on certain stock keeping units (SKUs) of the processors. SST-Performance Enables you to reconfigure the processor using Speed Select Technology. Profile x2APIC Mode Enables or disables the x2APIC mode. This option is set to Enabled by default. Dell Controlled Turbo Controls the turbo engagement. Enable this option only when System Profile is set to Disabled. NOTE: Depending on the number of installed processors, there might be up to two processor listings. Pre-operating system management applications 39
![](/manual_guide/products/dell-poweredge-c4140-emc-installation-service-manual-9ffb8d4/39.png)