Dell PowerEdge C4140 EMC Installation and Service Manual - Page 95

Installing the network daughter card

Get Dell PowerEdge C4140 PDF manuals and user guides View all Dell PowerEdge C4140 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

Figure 62. Removing the network daughter card Next steps Replace the network daughter card. Installing the network daughter card Prerequisites Follow the safety guidelines listed in Safety instructions on page 57. Steps 1. Orient the NDC so that the Ethernet connectors fit through the slot in the chassis. 2. Align the captive screws at the back-end of the card with the screw holes on the system board. 3. Press the touch points on the card until the card connector is firmly seated on the system board connector. 4. Using a Phillips #2 screwdriver, tighten the captive screws to secure the NDC to the system board. PowerEdge C4140 installing and removing system components 95

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
Figure 62. Removing the network daughter card
Next steps
Replace the network daughter card
.
Installing the network daughter card
Prerequisites
Follow the safety guidelines listed in
Safety instructions
on page 57.
Steps
1.
Orient the NDC so that the Ethernet connectors fit through the slot in the chassis.
2.
Align the captive screws at the back-end of the card with the screw holes on the system board.
3.
Press the touch points on the card until the card connector is firmly seated on the system board connector.
4.
Using a Phillips #2 screwdriver, tighten the captive screws to secure the NDC to the system board.
PowerEdge C4140 installing and removing system components
95