Dell PowerEdge C4140 EMC Installation and Service Manual - Page 71

Removing 2.5-inch cabled drives from the drive cage

Get Dell PowerEdge C4140 PDF manuals and user guides View all Dell PowerEdge C4140 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Figure 37. Installing the 2.5-inch drive cage cover Next steps 1. Install the drive cage into the PSU 2 bay. 2. Follow the procedure listed in After working inside your system. Removing 2.5-inch cabled drives from the drive cage Prerequisites NOTE: To identify the drive, see the label on the drive cable. For more information, see Drive Specifications. 1. Follow the safety guidelines listed in the Safety instructions section. 2. Follow the procedure listed in Before working inside your system. 3. Keep the Phillips #2 screwdriver ready. 4. Remove the 2.5-inch drive cage. 5. Remove the 2.5-inch drive cage cover. Steps 1. Remove the screws securing the drive to the drive cage. 2. Remove drives 0 and 1 by performing the following steps: a. Disconnect the signal and power cable from the drives. b. Lift drive 0 out of the drive cage. c. Slide drive 1 out of the drive cage. PowerEdge C4140 installing and removing system components 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
Figure 37. Installing the 2.5-inch drive cage cover
Next steps
1.
Install the drive cage into the PSU 2 bay
.
2.
Follow the procedure listed in
After working inside your system
.
Removing 2.5-inch cabled drives from the drive cage
Prerequisites
NOTE:
To identify the drive, see the label on the drive cable. For more information, see
Drive Specifications
.
1.
Follow the safety guidelines listed in the
Safety instructions
section.
2.
Follow the procedure listed in
Before working inside your system
.
3.
Keep the Phillips #2 screwdriver ready.
4.
Remove the 2.5-inch drive cage
.
5.
Remove the 2.5-inch drive cage cover
.
Steps
1.
Remove the screws securing the drive to the drive cage.
2.
Remove drives 0 and 1 by performing the following steps:
a.
Disconnect the signal and power cable from the drives.
b.
Lift drive 0 out of the drive cage.
c.
Slide drive 1 out of the drive cage.
PowerEdge C4140 installing and removing system components
71