Dell PowerEdge R750 EMC Installation and Service Manual - Page 61

Installing the 4 x 2.5-inch rear drive module

Get Dell PowerEdge R750 PDF manuals and user guides View all Dell PowerEdge R750 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Figure 55. Removing the 4 x 2.5-inch rear drive module Next steps 1. Replace the 4 x 2.5-inch rear drive module. Installing the 4 x 2.5-inch rear drive module Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. If required, remove the air shroud. 4. Remove the drives. 5. If installed, remove the BOSS S2 module. 6. Disconnect the cables from the rear drive module. NOTE: Refer cable routing topic for more information. Steps 1. Align and lower the rear drive module with the guide on the system board. 2. Using a Phillips #2 screwdriver, tighten the captive screws that secures the rear drive module into the system. Installing and removing system components 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
Figure 55. Removing the 4 x 2.5-inch rear drive module
Next steps
1.
Replace the 4 x 2.5-inch rear drive module
.
Installing the 4 x 2.5-inch rear drive module
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
If required,
remove the air shroud
.
4.
Remove the drives
.
5.
If installed,
remove the BOSS S2 module
.
6.
Disconnect the cables from the rear drive module.
NOTE:
Refer
cable routing
topic for more information.
Steps
1.
Align and lower the rear drive module with the guide on the system board.
2.
Using a Phillips #2 screwdriver, tighten the captive screws that secures the rear drive module into the system.
Installing and removing system components
61