Dell PowerVault LTO4-120HH Dell DR Series System Administrator's Guide - Page 39

Accessing iDRAC6/iDRAC7 Using RACADM, Logging in Using a Web Interface

Get Dell PowerVault LTO4-120HH PDF manuals and user guides View all Dell PowerVault LTO4-120HH manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

11. To change the default host name (for example, the serial number of the DR Series hardware appliance), type y (for yes) and press . If you responded yes, type the host name you want to use, and press . If you did not want to change the default host name, type n (for no) and press . After you configure your host name response, the current system settings are displayed. 12. To accept these settings, type y (for yes), and press . 13. If you want to change any of these settings, type n (for no), and press . Modify the settings as needed, and press . When completed, a successful initialization message is displayed. 14. At the prompt, type exit and press to end the DR Series system CLI session. You are now ready to log in to the system using the DR Series system GUI. NOTE: Before you log into the system using the DR Series system GUI, make sure to register it in the local Domain Name System (DNS) for your network so that it is a DNS-resolvable entry. NOTE: At this point, you could modify the bonding mode to use 802.3ad, if this configuration is available in your network. Accessing iDRAC6/iDRAC7 Using RACADM You can use SSH-based or Telnet-based interfaces to access iDRAC6/iDRAC7 using the RACADM utility. RACADM (remote access controller administration) is a Dell command-line utility that allows you to set up and configure the integrated Dell Remote Access Control (iDRAC) interface card to provide an out-of-band management capability. The iDRAC card contains a controller with its own processor, memory, network connection, and access to the system bus. This gives system or network administrators the capability to configure a system as if they were sitting at the local console using the power management, virtual medial access and remote console capabilities, by using a supported web browser or command line interface. The login values you can use for making iDRAC connections are: • Default username: root • Default password: calvin • Default static IP address: 192.168.0.120 For more information, see the RACADM Reference Guides for iDRAC, the Integrated Dell Remote Access Controller 6 (iDRAC6) User Guide, or the Integrated Dell Remote Access Controller 7 (iDRAC7) User Guide that are available at support.dell.com/manuals. Logging in Using a Web Interface To log in to the DR Series system using a browser-based connection, complete the following: NOTE: This procedure describes the logging in process from a first-time perspective, starting with the Customer Registration and Notification page, the completion of the Initial System Configuration Wizard process, and the Initial Software Upgrade page. 1. In a supported web browser, type the IP address or hostname of the system in the browser Address bar, and press . The DR Series System Login page is displayed. 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
11.
To change the default host name (for example, the serial number of the DR Series hardware appliance), type
y
(for
yes) and press
<Enter>
.
If you responded
yes
, type the host name you want to use, and press
<Enter>
. If you did not want to change the
default host name, type
n
(for no) and press
<Enter>
. After you configure your host name response, the current
system settings are displayed.
12.
To accept these settings, type
y
(for yes), and press
<Enter>
.
13.
If you want to change any of these settings, type
n
(for no), and press
<Enter>
. Modify the settings as needed, and
press
<Enter>
.
When completed, a successful initialization message is displayed.
14.
At the prompt, type
exit
and press
<Enter>
to end the DR Series system CLI session.
You are now ready to log in to the system using the DR Series system GUI.
NOTE:
Before you log into the system using the DR Series system GUI, make sure to register it in the local Domain
Name System (DNS) for your network so that it is a DNS-resolvable entry.
NOTE:
At this point, you could modify the bonding mode to use 802.3ad, if this configuration is available in your
network.
Accessing iDRAC6/iDRAC7 Using RACADM
You can use SSH-based or Telnet-based interfaces to access iDRAC6/iDRAC7 using the RACADM utility. RACADM
(remote access controller administration) is a Dell command-line utility that allows you to set up and configure the
integrated Dell Remote Access Control (iDRAC) interface card to provide an out-of-band management capability.
The iDRAC card contains a controller with its own processor, memory, network connection, and access to the system
bus. This gives system or network administrators the capability to configure a system as if they were sitting at the local
console using the power management, virtual medial access and remote console capabilities, by using a supported web
browser or command line interface.
The login values you can use for making iDRAC connections are:
•
Default username:
root
•
Default password:
calvin
•
Default static IP address:
192.168.0.120
For more information, see the
RACADM Reference Guides for iDRAC
, the
Integrated Dell Remote Access Controller 6
(iDRAC6) User Guide
, or the
Integrated Dell Remote Access Controller 7 (iDRAC7) User Guide
that are available at
support.dell.com/manuals
.
Logging in Using a Web Interface
To log in to the DR Series system using a browser-based connection, complete the following:
NOTE:
This procedure describes the logging in process from a first-time perspective, starting with the
Customer
Registration and Notification
page, the completion of the
Initial System Configuration Wizard
process, and the
Initial Software Upgrade
page.
1.
In a supported web browser, type the IP address or hostname of the system in the browser
Address bar
, and press
<Enter>
.
The
DR Series System Login
page is displayed.
39