Epson R200 Service Manual - Page 18

Table 1-7., Check Points for Paper Jam Error to Each Phenomenon - stylus photo printer troubleshooting

Get Epson R200 - Stylus Photo Color Inkjet Printer PDF manuals and user guides
UPC - 010343849532
View all Epson R200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

EPSON Stylus Photo R200/R210 Revision A Occurrence Timing Position of CR Phenomenon Detail "PF Motor" does not work at all. Table 1-7. Check Points for Paper Jam Error to Each Phenomenon Faulty Part/ Part Name Check Point Remedy PF Motor 1. Check if "PF Motor Connector Cable" is connected to CN6 on "Main Board". 2. Check if the coil resistance of "PF Motor" is approximately 3.0W with a tester. Refer to Table 1-1. 3. Check if "PF Motor Connector Cable" is damaged. 1. Check if "Roller, Retard Assy." operates properly while feeding paper. 1. Connect "PF Motor Connector Cable" to CN6 on "Main Board". 2. Replace "PF Motor" with a new one. 3. Replace "PF Motor" with a new one. 1. Reassemble "Extension Spring, 0.45" located the under side of "Roller, Retard Assy.". ASF Assy. At power-on Anywhere Paper feeding operation is performed normally, but paper is not sent into the printer. 1. Check if "Torsion Spring, 0.22" is not unfastened from "PE Sensor Lever". Extension Spring, 0.45 1. Reassemble "Torsion Spring, 0.22" PE Sensor Torsion Spring, 0.22 2. Check if "PE Sensor Cable" is not unfastened. 3. Check if "PE Sensor Cable" is correctly mounted on "Holder, Shaft, LD Roller". 4. Check if "PE Sensor Cable" is not damaged. 2. Connect "PE Sensor" Connector to CN9 on "Main Board". 3. Remount "PE Sensor Cable" correctly. 4. Replace "PE Sensor" with a new one. TROUBLESHOOTING Unit Level Troubleshooting 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
EPSON Stylus Photo R200/R210
Revision A
TROUBLESHOOTING
Unit Level Troubleshooting
18
Table 1-7.
Check Points for Paper Jam Error to Each Phenomenon
Occurrence
Timing
Position of CR
Phenomenon Detail
Faulty Part/
Part Name
Check Point
Remedy
At power-on
Anywhere
"PF Motor" does not work at all.
PF Motor
1.
Check if "PF Motor Connector Cable" is connected to
CN6 on "Main Board".
2.
Check if the coil resistance of "PF Motor" is
approximately 3.0
±
with a tester. Refer to Table 1-1.
3.
Check if "PF Motor Connector Cable" is damaged.
1.
Connect "PF Motor Connector Cable" to CN6
on "Main Board".
2.
Replace "PF Motor" with a new one.
3.
Replace "PF Motor" with a new one.
Paper feeding operation is performed
normally, but paper is not sent into the
printer.
ASF Assy.
1.
Check if "Roller, Retard Assy." operates properly while
feeding paper.
1.
Reassemble "Extension Spring, 0.45" located
the under side of "Roller, Retard Assy.".
PE Sensor
1.
Check if "Torsion Spring, 0.22" is not unfastened from
"PE Sensor Lever".
2.
Check if "PE Sensor Cable" is not unfastened.
3.
Check if "PE Sensor Cable" is correctly mounted on
"Holder, Shaft, LD Roller".
4.
Check if "PE Sensor Cable" is not damaged.
1.
Reassemble "Torsion Spring, 0.22"
2.
Connect "PE Sensor" Connector to CN9 on
"Main Board".
3.
Remount "PE Sensor Cable" correctly.
4.
Replace "PE Sensor" with a new one.
Extension
Spring, 0.45
Torsion Spring, 0.22