Epson R200 Service Manual - Page 46

Be careful not to damage PE Sensor Lever and Paper Guide

Get Epson R200 - Stylus Photo Color Inkjet Printer PDF manuals and user guides
UPC - 010343849532
View all Epson R200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

EPSON Stylus Photo R200/R210 2.3.8 Holder, Shaft Unit removal o External View Backside Hook CN7, CN8, CN15 C.B.S 3x6 (6-8kgf/cm) Dowel C.B.S 3x6 (6-8kgf/cm) PE sensor Board, Main CN9 CN5 Shield Plate, FFC Hook Head FFC Hook Right front side Hook Hook Figure 2-13. "Holder, Shaft Unit" removal (1) Revision A o Parts/Units which should be removed before removing "Holder, Shaft Unit" Paper Support Assy./Housing (left/right)/Housing (frame)/ASF Assy. o Disassembly Procedure n Holder, Shaft Unit removal 1. Release the following connector cables from "Board, Main". CN5 CN7 CN8 CN9 CN15 : CR motor connector cable : Head FFC : Head FFC : PE sensor connector cable : CSIC/CR encoder/PW sensor FFC 2. Release the CR motor connector cable from "Holder, Shaft Unit". 3. Move "Carriage Unit" to the left side of the printer. 4. Remove the screws (x2) for securing "Holder, Shaft Unit". 5. Release the Head FFC with "Shield Plate, FFC" from "Holder, Shaft Unit". C A U T IO N o Do not use "Shield Plate, FFC" again if you peel it off. o Do not damage "Shield Plate, FFC". o Do not damage "Cable, Head". 6. Release the hooks ( 1 : x2) with the tweezers or alike while pulling"Holder, Shaft Unit" upward, and release the dowel ( 2 : x1) from "Ink System Frame". 7. Looking at the printer from its back side, press down "Paper Guide, Upper" on the left, and release "PE Sensor Lever" from the slot. Then, remove "Holder, Shaft Assy." by sliding it to the right. C A U T IO N Be careful not to damage "PE Sensor Lever" and "Paper Guide, Upper" when removing them since "PE Sensor Lever" contacts with "Paper Guide, Upper". DISASSEMBLY AND ASSEMBLY Disassembly 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
EPSON Stylus Photo R200/R210
Revision A
DISASSEMBLY AND ASSEMBLY
Disassembly
46
2.3.8
Holder, Shaft Unit removal
±
External View
Figure 2-13.
"Holder, Shaft Unit" removal (1)
±
Parts/Units which should be removed before removing "Holder, Shaft Unit"
Paper Support Assy./Housing (left/right)/Housing (frame)/ASF Assy.
±
Disassembly Procedure
²
Holder, Shaft Unit removal
1.
Release the following connector cables from "Board, Main".
CN5
: CR motor connector cable
CN7
: Head FFC
CN8
: Head FFC
CN9
: PE sensor connector cable
CN15
: CSIC/CR encoder/PW sensor FFC
2.
Release the CR motor connector cable from "Holder, Shaft Unit".
3.
Move "Carriage Unit" to the left side of the printer.
4.
Remove the screws (x2) for securing "Holder, Shaft Unit".
5.
Release the Head FFC with "Shield Plate, FFC" from "Holder, Shaft Unit".
6.
Release the hooks (
: x2) with the tweezers or alike while pulling"Holder,
Shaft Unit" upward, and release the dowel (
: x1) from "Ink System Frame".
7.
Looking at the printer from its back side, press down "Paper Guide, Upper" on
the left, and release "PE Sensor Lever" from the slot. Then, remove "Holder,
Shaft Assy." by sliding it to the right.
2
C.B.S 3x6 (6-8kgf/cm)
Board, Main
CN5
CN9
Backside
1
1
C.B.S 3x6 (6-8kgf/cm)
CN7, CN8, CN15
Shield Plate, FFC
Head FFC
Hook
Hook
Hook
Hook
Hook
Right front side
Dowel
PE sensor
C
A
U
T
I
O
N
±
Do not use "Shield Plate, FFC" again if you peel it off.
±
Do not damage "Shield Plate, FFC".
±
Do not damage "Cable, Head".
C
A
U
T
I
O
N
Be careful not to damage "PE Sensor Lever" and "Paper Guide,
Upper" when removing them since "PE Sensor Lever" contacts
with "Paper Guide, Upper".
1
2