Epson R200 Service Manual - Page 85

PG Checking 1, PG Checking 2

Get Epson R200 - Stylus Photo Color Inkjet Printer PDF manuals and user guides
UPC - 010343849532
View all Epson R200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

EPSON Stylus Photo R200/R210 Revision A 9. After finishing PG Adjustment on the right, move "Carriage Unit" to the left edge again, then check PG according to the flowchart in the Figure 3-11. Start Move "Carriage Unit" to the right by using "Timing Belt". Note: Take down toward the printer front by 1 notch: PG gets narrower. Take up toward the printer back by 1 notch: PG gets wider. Yes Does the Thickness Gauge move? No Go to Step 10 Take up "Bushing, Parallel Adjust, Left" toward the printer back by 1 notch. Take up: PG gets wider Move "Carriage Unit" to the right by using "Timing Belt". Does the Thickness Yes Gauge move? Take down: PG gets narrower No Go Back to Step 7 Figure 3-11. PG Checking (1) 10. Move "Carriage Unit" back to the left edge of the printer, then set the Thickness Gauge (1.31mm) on the ribs (X3) of "Paper Guide, Front" in the same way as the Figure 3-7. 11. Check PGs on both the left and right according to the flowchart in the Figure 3-12. Start Check left PG. Move "Carriage Unit" to the right by using "Timing Belt". No Does the Thickness Gauge move? Yes Check right PG. Move "Carriage Unit" to the left by using "Timing Belt". Does the Thickness No Gauge move? Yes Go to Step 12 Go Back to Step 3 Figure 3-12. PG Checking (2) 12. After finishing the adjustment, screw "Bushing, Parallel Adjust, Left (Right)". 13. After screwing, check PGs on both the left and right again according to the flowchart in the Figure 3-12. ADJUSTMENT Adjustment Except Adjustment Program 85

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
EPSON Stylus Photo R200/R210
Revision A
ADJUSTMENT
Adjustment Except Adjustment Program
85
9.
After finishing PG Adjustment on the right, move "Carriage Unit" to the left edge
again, then check PG according to the flowchart in the Figure 3-11.
Figure 3-11. PG Checking (1)
10.
Move "Carriage Unit" back to the left edge of the printer, then set the Thickness
Gauge (1.31mm) on the ribs (X3) of "Paper Guide, Front" in the same way as the
Figure 3-7.
11.
Check PGs on both the left and right according to the flowchart in the Figure 3-12.
Figure 3-12. PG Checking (2)
12.
After finishing the adjustment, screw "Bushing, Parallel Adjust, Left (Right)".
13.
After screwing, check PGs on both the left and right again according to the
flowchart in the Figure 3-12.
Yes
No
Take up: PG gets wider
Take down: PG gets narrower
Go to Step 10
Start
Take up "Bushing, Parallel
Adjust, Left" toward the
printer back by 1 notch.
Move "Carriage Unit" to
the right by using
"Timing Belt".
Does the Thickness
Gauge move?
Yes
No
Move "Carriage Unit" to
the right by using
"Timing Belt".
Does the Thickness
Gauge move?
Go Back to Step 7
Note:
Take down toward the printer front by 1 notch:
PG gets narrower.
Take up toward the printer back by 1 notch:
PG gets wider.
No
Yes
Start
Go Back to Step 3
Check left PG.
No
Yes
Check right PG.
Go to Step 12
Move "Carriage Unit" to
the right by using
"Timing Belt".
Does the Thickness
Gauge move?
Move "Carriage Unit" to
the left by using "Timing
Belt".
Does the Thickness
Gauge move?