Epson R200 Service Manual - Page 45

Replace Waste Ink Pads with new one. - ink pad replacement

Get Epson R200 - Stylus Photo Color Inkjet Printer PDF manuals and user guides
UPC - 010343849532
View all Epson R200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

EPSON Stylus Photo R200/R210 2.3.7 Board, Main removal o External View Shield Plate Board, Main Figure 2-12. Board, Main removal o Pars/Units which should be removed before removing "Board, Main" Paper Support Assy./Housing (left/right)/Housing (frame)/ASF Unit o Disassembly Procedure 1. Disconnect all connector cables from "Board, Main". CN2 CN4 CN5 CN6 CN7 CN8 CN9 CN10 CN11 CN13 CN14 CN15 : Power supply connector cable : Panel board connector cable : CR motor connector cable : PF motor connector cable : Head FFC : Head FFC : PE sensor connector cable : Interface board connector cable : CDR tray sensor cable : APG motor connecor cable : PG sensor cable : CSIC/CR encoder /PW sensor FFC 2. Remove the screws (x4) for securing "Board, Main"with the order in figure, and remove "Board, Main". Revision A 3. Remove "Shield Plate, M/B" from "Board, M/B". o When reinstalling "Board, Main", n Make sure that all cables/FFCs are correctly connected to the appropriciate connector of "Board, Main". n Make sure to secure the screws in the order as shown in the figure. A D JU S TM E N T R E Q U IR E D o When having replaced "Main Board", implement the adjustment in the following order. (Refer to Chapter 3 "ADJUSTMENT") n When possible to read data from the old board 1. EEPROM data copy n When impossible to read from the old board 1. Replace "Waste Ink Pads" with new one. (To count the amount of the waste ink) 2. Market Setting 3. USB ID Input 4. Waste Ink Pad Counter 5. Head ID Input 6. First Dot Adjustment 7. PW Sensor Adjustment 8. Head Angular Adjustment 9. Bi-D Adjustment 10. Offset Input for CR Motor Calorific Limitation DISASSEMBLY AND ASSEMBLY Disassembly 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
EPSON Stylus Photo R200/R210
Revision A
DISASSEMBLY AND ASSEMBLY
Disassembly
45
2.3.7
Board, Main removal
±
External View
Figure 2-12.
Board, Main removal
±
Pars/Units which should be removed before removing "Board, Main"
Paper Support Assy./Housing (left/right)/Housing (frame)
/ASF Unit
±
Disassembly Procedure
1.
Disconnect all connector cables from "Board, Main".
CN2
: Power supply connector cable
CN4
: Panel board connector cable
CN5
: CR motor connector cable
CN6
: PF motor connector cable
CN7
: Head FFC
CN8
: Head FFC
CN9
: PE sensor connector cable
CN10
: Interface board connector cable
CN11
: CDR tray sensor cable
CN13
: APG motor connecor cable
CN14
: PG sensor cable
CN15
: CSIC/CR encoder /PW sensor FFC
2.
Remove the screws (x4) for securing "Board, Main"with the order in figure, and
remove "Board, Main".
3.
Remove "Shield Plate, M/B" from "Board, M/B".
1
2
3
C.B.S 3x10 (5-7kgf/cm)
4
C.B.S 3x6 (5-7kgf/cm)
Board, Main
Shield Plate
，M/B
±
When reinstalling "Board, Main",
²
Make sure that all cables/FFCs are correctly connected to
the appropriciate connector of "Board, Main".
²
Make sure to secure the screws in the order as shown in the
figure.
A
D
J
U
S
T
M
E
N
T
R
E
Q
U
I
R
E
D
±
When having replaced "Main Board", implement the
adjustment in the following order. (Refer to Chapter 3
"ADJUSTMENT")
²
When possible to read data from the old board
1.
EEPROM data copy
²
When impossible to read from the old board
1.
Replace "Waste Ink Pads" with new one.
(To count the amount of the waste ink)
2.
Market Setting
3.
USB ID Input
4.
Waste Ink Pad Counter
5.
Head ID Input
6.
First Dot Adjustment
7.
PW Sensor Adjustment
8.
Head Angular Adjustment
9.
Bi-D Adjustment
10.
Offset Input for CR Motor Calorific Limitation