Gateway 995 995 Series Server User Guide - Page 76

Installing a tape drive

Get Gateway 995 PDF manuals and user guides View all Gateway 995 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

Chapter 4: Installing Components 7 Slide the cage out of the server toward the front. 8 Slide the new hard drive cage into the cage bay until it clicks into place. 9 Reconnect the three power cables and one SCSI ribbon cable to the back of the cage. 10 Reinstall each hard drive into the slot it was removed from, then reinstall each panel that was removed. Installing a tape drive Warning Although the tape drive bay is capable of holding a hard drive, to maintain correct cooling you should not install a hard drive in this bay. To install a tape drive: 1 Follow the instructions in "Preventing static electricity discharge" on page 36. Make sure that you turn off the server, then unplug the power cords and all other cables connected to the server. 2 Remove the front cover, if installed. For instructions, see "Using the front cover" on page 39. 70 www.gateway.com

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
70
Chapter 4: Installing Components
www.gateway.com
7
Slide the cage out of the server toward the front.
8
Slide the new hard drive cage into the cage bay until it clicks into place.
9
Reconnect the three power cables and one SCSI ribbon cable to the back
of the cage.
10
Reinstall each hard drive into the slot it was removed from, then reinstall
each panel that was removed.
Installing a tape drive
To install a tape drive:
1
Follow the instructions in
“Preventing static electricity discharge” on
page 36
. Make sure that you turn off the server, then unplug the power
cords and all other cables connected to the server.
2
Remove the front cover, if installed. For instructions, see
“Using the front
cover” on page 39
.
Warning
Although the tape drive bay is capable of holding a hard
drive, to maintain correct cooling you should not install a
hard drive in this bay.