Gateway 995 995 Series Server User Guide - Page 92

Installing memory

Get Gateway 995 PDF manuals and user guides View all Gateway 995 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

Chapter 4: Installing Components Installing memory Your server supports from 512 MB to 24 GB total memory. Caution Modules must be installed in identical groups of four. Use only PC1600 (DDR-200) or PC2100 (DDR-266) compliant, SDRAM registered ECC, DIMM memory modules. Install memory first into Bank 1, Bank 2, then Bank 3. If memory is installed incorrectly, your server will not start. Partially filled banks are ignored by the server. For the most reliable and stable operation, we recommend you use memory from the same manufacturer in all memory banks. Bank 3 Bank 2 Bank 1 To add or replace memory modules: 1 Follow the instructions in "Preventing static electricity discharge" on page 36. Make sure that you turn off the server, then unplug the power cords and all other cables connected to the server. 2 Remove the top rear panel. For instructions, see "Removing the top rear panel" on page 41. 3 Remove the inside panel. For instructions, see "Removing the inside panel" on page 45. 86 www.gateway.com

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
86
Chapter 4: Installing Components
www.gateway.com
Installing memory
Your server supports from 512 MB to 24 GB total memory.
To add or replace memory modules:
1
Follow the instructions in
“Preventing static electricity discharge” on
page 36
. Make sure that you turn off the server, then unplug the power
cords and all other cables connected to the server.
2
Remove the top rear panel. For instructions, see
“Removing the top rear
panel” on page 41
.
3
Remove the inside panel. For instructions, see
“Removing the inside panel”
on page 45
.
Caution
Modules must be installed in identical groups of four. Use
only PC1600 (DDR-200) or PC2100 (DDR-266) compliant,
SDRAM registered ECC, DIMM memory modules.
Install memory first into Bank 1, Bank 2, then Bank 3. If
memory is installed incorrectly, your server will not start.
Partially filled banks are ignored by the server.
For the most reliable and stable operation, we recommend
you use memory from the same manufacturer in all
memory banks.
Bank 1
Bank 2
Bank 3