HP Latex 560 User Guide - Page 74

Edge holders, WARNING, Place edge holders

Get HP Latex 560 PDF manuals and user guides View all HP Latex 560 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

4. Select the category and name of the substrate you are loading. The rest of the assisted load procedure is the same as in the normal load procedure. See Load a roll into the printer on page 51. Edge holders The edge holders are designed to prevent the edges of the substrate from rising while printing is in progress. They are recommended only when the edges of the substrate tend to lift up and touch or damage the printheads. They can be used with the platen or with the ink collector. When not in use, they should be stored outside the printer. If they are needed often, they can be stored inside the printer, to the left and right of the print platen, to avoid substrate jams when loading the next substate. NOTE: The edge holders extend 7 mm over the edge of the substrate. You should set a minimum left and right margin of 7 mm (0.3 in) in the RIP when using edge holders, otherwise the printer could try to print on the edge holders. If you choose to use them, you should move them into position when prompted by the front panel (this prompt appears when the Use edge holders checkbox has been checked). Open the window, place the edge holders, then close the window. The edge holders should be placed on the platen so that they overlap the left and right edges of the substrate. Align the dotted line on the edge holder with the lateral edge of the substrate. WARNING! Avoid moving parts. Handle fragile parts with care. You are recommended to wear gloves. Moving part Fragile For more safety information, please see Safety precautions on page 3 Wear gloves Place edge holders 1. Remove the platen module or ink collector on one side of the printer. 68 Chapter 3 Handle the substrate and troubleshoot substrate issues ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
4.
Select the category and name of the substrate you are loading.
The rest of the assisted load procedure is the same as in the normal load procedure. See
Load a roll into the
printer
on page
51
.
Edge holders
The edge holders are designed to prevent the edges of the substrate from rising while printing is in progress.
They are recommended only when the edges of the substrate tend to lift up and touch or damage the
printheads. They can be used with the platen or with the ink collector. When not in use, they should be stored
outside the printer.
If they are needed often, they can be stored inside the printer, to the left and right of the print platen, to avoid
substrate jams when loading the next substate.
NOTE:
The edge holders extend 7 mm over the edge of the substrate. You should set a minimum left and right
margin of 7 mm (0.3 in) in the RIP when using edge holders, otherwise the printer could try to print on the edge
holders.
If you choose to use them, you should move them into position when prompted by the front panel (this prompt
appears when the
Use edge holders
checkbox has been checked). Open the window, place the edge holders,
then close the window.
The edge holders should be placed on the platen so that they overlap the left and right edges of the substrate.
Align the dotted line on the edge holder with the lateral edge of the substrate.
WARNING!
Avoid moving parts. Handle fragile parts with care. You are recommended to wear gloves.
Moving part
Fragile
Wear gloves
For more safety information, please see
Safety precautions
on page
3
Place edge holders
1.
Remove the platen module or ink collector on one side of the printer.
68
Chapter 3
Handle the substrate and troubleshoot substrate issues
ENWW