HP XM600 hp kayak xm600 series 2, user's guide for desktop models - Page 29

Removing and Replacing an Accessory Card, card in place and carefully pull it out.

Get HP XM600 - Kayak - 128 MB RAM PDF manuals and user guides View all HP XM600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

2 Installing and Replacing Hardware Parts in Your PC Workstation Removing and Replacing an Accessory Card Removing and Replacing an Accessory Card The HP Kayak XM600 has five 32-bit 33 MHz PCI accessory card slots and one AGP slot on the system board. The AGP slot accepts standard 25W AGP video cards. NOTE AGP PRO video cards cannot be used in desktop models. Hardware Protection on the system board ensures that the system is protected against this. 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstation's cover (refer to page 22 for instructions). 3 If you are installing a new accessory card, unscrew and remove the slot panel. Store it in a safe place. If the slot cover is tight, loosen the screws on the adjacent slots. If you are replacing an existing accessory card, remove any cables connected to the accessory card. Remove the screw that holds the old card in place and carefully pull it out. NOTE Some cards may have preferred locations and special installation instructions detailed in their manuals. 4 Aligning the new card carefully, slide it into position, then press it firmly into the slot and tighten the retaining screw. 5 Install any other accessories before replacing the cover (refer to page 23). Reconnect all the power and telecommunications cables. 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
2
Installing and Replacing Hardware Parts in Your PC Workstation
Removing and Replacing an Accessory Card
29
Removing and Replacing an Accessory Card
The HP Kayak XM600 has five 32-bit 33 MHz PCI accessory card slots and
one AGP slot on the system board. The AGP slot accepts standard 25W
AGP video cards.
NOTE
AGP PRO video cards cannot be used in desktop models. Hardware
Protection on the system board ensures that the system is protected
against this.
1
Switch off the display and PC Workstation. Disconnect all power cables
and any LAN or telecommunications cables.
2
Remove the PC Workstation’s cover (refer to page 22 for instructions).
3
If you are installing a new accessory card, unscrew and remove the slot
panel. Store it in a safe place. If the slot cover is tight, loosen the screws
on the adjacent slots.
If you are replacing an existing accessory card, remove any cables
connected to the accessory card. Remove the screw that holds the old
card in place and carefully pull it out.
NOTE
Some cards may have preferred locations and special installation
instructions detailed in their manuals.
4
Aligning the new card carefully, slide it into position, then press it firmly
into the slot and tighten the retaining screw.
5
Install any other accessories before replacing the cover (refer to page
23). Reconnect all the power and telecommunications cables.