HP XM600 hp kayak xm600 series 2, user's guide for desktop models - Page 30

Installing Mass Storage Devices

Get HP XM600 - Kayak - 128 MB RAM PDF manuals and user guides View all HP XM600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

2 Installing and Replacing Hardware Parts in Your PC Workstation Installing Mass Storage Devices Installing Mass Storage Devices The PC has an integrated Ultra ATA-66 controller that supports up to four IDE devices. Removable media IDE devices, such as CD-ROM drives, DVD drives, tape drives and Zip drives, require front access. In addition to the floppy disk drive, your PC can support another 3.5-inch internal device plus two front-access 5.25-inch devices. Note that one front-access shelf may already have a CD-ROM drive installed in it. You can physically install up to two 10K RPM hard disk drives in the desktop chassis. Refer to the drive's manual to see if you must set jumpers or if there is a special installation procedure to follow. Cables and Connectors (all models) If you add an IDE Zip drive, hard disk drive, DVD drive, CD-ROM drive, CDRW drive, or tape drive, you need to connect it to power and data cables. The data cables and connectors provided are shown below: Primary IDE cable supports two Hard Disk Drives Two IDE data cables each with two 40-pin connectors for IDE Drives Secondary IDE cable for access devices such as CD-ROM Drives or Zip Drives Primary IDE Connector Secondary IDE Connector Cable with one 34-pin connector for 3.5-inch Floppy Disk Drive Floppy Disk Drive Connector 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
2
Installing and Replacing Hardware Parts in Your PC Workstation
Installing Mass Storage Devices
30
Installing Mass Storage Devices
The PC has an integrated Ultra ATA-66 controller that supports up to four
IDE devices. Removable media IDE devices, such as CD-ROM drives, DVD
drives, tape drives and Zip drives, require front access. In addition to the
floppy disk drive, your PC can support another 3.5-inch internal device plus
two front-access 5.25-inch devices. Note that one front-access shelf may
already have a CD-ROM drive installed in it.
You can physically install up to two 10K RPM hard disk drives in the
desktop chassis.
Refer to the drive’s manual to see if you must set jumpers or if there is a
special installation procedure to follow.
Cables and Connectors (all models)
If you add an IDE Zip drive, hard disk drive, DVD drive, CD-ROM drive, CD-
RW drive, or tape drive, you need to connect it to power and data cables.
The data cables and connectors provided are shown below:
Cable with one 34-pin
connector for
3.5-inch Floppy Disk Drive
Floppy Disk Drive Connector
Primary IDE
Connector
Secondary IDE Connector
Two IDE data cables each
with two 40-pin connectors
for IDE Drives
Primary IDE cable supports
two Hard Disk Drives
Secondary IDE cable for access devices
such as CD-ROM Drives or Zip Drives