HP XM600 hp kayak xm600 series 2, user's guide for desktop models - Page 40

Replacing the Hard Drive Bay and Speaker Assembly, Removing the Assembly

Get HP XM600 - Kayak - 128 MB RAM PDF manuals and user guides View all HP XM600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

2 Installing and Replacing Hardware Parts in Your PC Workstation Replacing the Hard Drive Bay and Speaker Assembly Replacing the Hard Drive Bay and Speaker Assembly Removing the Assembly 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstation's cover and front bezel (refer to page 23 for these instructions). 3 Remove the two primary hard disk retaining screws located on the front left side of the chassis and lift the primary hard disk drive out of the hard disk drive bay. 4 Disconnect the data and power cables from the primary hard disk drive. If you have a second hard disk drive installed, disconnect its data and power cables. 5 Remove the two secondary disk tray retaining screws located on the front centre of the chassis, then slide the tray towards the rear of the PC and remove it. 6 Disconnect the speaker and control panel cables from their connectors on the system board. 7 From the front of the PC: (a) push the two plastic clips located on the left-hand side inwards; (b) repeat this procedure for the other two clips on the right-hand side.  ž a b 8 Unclip the retention clip located on the right-hand side and middle of the hard disk drive bay and speaker assembly. 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
2
Installing and Replacing Hardware Parts in Your PC Workstation
Replacing the Hard Drive Bay and Speaker Assembly
40
Replacing the Hard Drive Bay and Speaker Assembly
Removing the Assembly
1
Switch off the display and PC Workstation. Disconnect all power cables
and any LAN or telecommunications cables.
2
Remove the PC Workstation’s cover and front bezel (refer to page 23 for
these instructions).
3
Remove the two primary hard disk retaining screws located on the front left
side of the chassis and lift the primary hard disk drive out of the hard disk
drive bay.
4
Disconnect the data and power cables from the primary hard disk drive.
If you have a second hard disk drive installed, disconnect its data and
power cables.
5
Remove the two secondary disk tray retaining screws located on the front
centre of the chassis, then slide the tray towards the rear of the PC and
remove it
.
6
Disconnect the speaker and control panel cables from their connectors
on the system board.
7
From the front of the PC: (a) push the two plastic clips located on the
left-hand side inwards; (b) repeat this procedure for the other two clips
on the right-hand side.
8
Unclip the retention clip located on the right-hand side and middle of the
hard disk drive bay and speaker assembly.
³
b
a