HP XM600 hp kayak xm600 series 2, user's guide for desktop models - Page 42

Completing the Installation of a Mass Storage Device, When a Floppy Disk

Get HP XM600 - Kayak - 128 MB RAM PDF manuals and user guides View all HP XM600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

2 Installing and Replacing Hardware Parts in Your PC Workstation Completing the Installation of a Mass Storage Device When an IDE Drive Is Installed When a SCSI Hard Disk Drive Is Installed When a CD-ROM, CD-RW or DV-Drive is Installed When a Floppy Disk Drive Is Installed Completing the Installation of a Mass Storage Device 1 Switch on the PC Workstation. 2 To verify the configuration of your hard disk drive, press F2 to enter Setup when the HP logo appears. Once in Setup, select the Advanced menu, then the IDE Devices submenu. In the Primary Master item, check that the details for the device have been correctly detected by the Setup program. 3 Press F3 to save and exit Setup. 4 Refer to the operating system documentation for information on partitioning and formatting a drive. 5 If an IDE drive is removed, switch on the PC Workstation. The system BIOS will detect that the device is missing. Press F4 to confirm that you want to remove the device. The system configuration will be updated automatically. 1 Switch on the PC Workstation. 2 To enter the SCSI Configuration Utility press F6 when prompted during the PC Workstation's start-up routine. 3 Verify or modify the configuration of your new SCSI hard disk drive. For more information on configuring a SCSI hard disk drive, refer to the SCSI Administrator's Guide available on HP's web site at http://www.hp.com/go/kayaksupport. 4 When configuration is complete, exit the SCSI Configuration Utility and re-boot the PC Workstation to save any changes. 1 Switch on the PC Workstation and press F2 when the HP logo appears. 2 In the Setup program, select the Advanced menu, then the IDE Devices submenu. Check that the CD-ROM drive has been detected on the IDE channel. 3 Press F3 to save and exit the program. 1 Switch on the PC Workstation and press F2 when HP logo appears. 2 In the Setup program, select the Advanced menu, then the Floppy Disk Drives submenu, and check that the drive has been detected. 3 Press F3 to save and exit the program. 42

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
2
Installing and Replacing Hardware Parts in Your PC Workstation
Completing the Installation of a Mass Storage Device
42
Completing the Installation of a Mass Storage Device
When an IDE Drive
Is Installed
1
Switch on the PC Workstation.
2
To verify the configuration of your hard disk drive, press
F2
to enter
Setup
when the HP logo appears. Once in
Setup
, select the
Advanced
menu, then the
IDE Devices
submenu. In the
Primary Master
item, check
that the details for the device have been correctly detected by the
Setup
program.
3
Press
F3
to save and exit
Setup
.
4
Refer to the operating system documentation for information on
partitioning and formatting a drive.
5
If an IDE drive is removed, switch on the PC Workstation. The system
BIOS will detect that the device is missing. Press
F4
to confirm that you
want to remove the device. The system configuration will be updated
automatically.
When a SCSI Hard
Disk Drive Is
Installed
1
Switch on the PC Workstation.
2
To enter the SCSI Configuration Utility press
F6
when prompted during
the PC Workstation’s start-up routine.
3
Verify or modify the configuration of your new SCSI hard disk drive.
For more information on configuring a SCSI hard disk drive, refer
to the
SCSI Administrator’s Guide
available on HP’s web site at
4
When configuration is complete, exit the SCSI Configuration Utility and
re-boot the PC Workstation to save any changes.
When a CD-ROM,
CD-RW or DV-Drive
is Installed
1
Switch on the PC Workstation and press
F2
when
the HP logo
appears.
2
In the
Setup
program, select the
Advanced
menu, then the
IDE Devices
submenu. Check that the CD-ROM drive has been detected on the IDE
channel.
3
Press
F3
to save and exit the program.
When a Floppy Disk
Drive Is Installed
1
Switch on the PC Workstation and press
F2
when
HP logo
appears.
2
In the
Setup
program, select the
Advanced
menu, then the
Floppy Disk
Drives
submenu, and check that the drive has been detected.
3
Press
F3
to save and exit the program
.