HP XM600 hp kayak xm600 series 2, user's guide for desktop models - Page 31

2

Installing and Replacing Hardware Parts in Your PC Workstation

Installing Mass Storage Devices

31

Which IDE Data

Connectors to Use

There are three data cables inside your PC Workstation. Two of these are

for IDE devices.

•

The ATA IDE cable supports two IDE devices. This cable is connected

to the Primary IDE connector on the system board. The bootable hard

disk drive is connected to this cable via the MASTER connector. A

second hard disk drive could be installed by using the SLAVE connector.

•

A second IDE drive cable supports two IDE devices. If you install a CD-

ROM drive, a DVD drive or a Zip drive, connect it to this cable.

•

The third cable has one connector for a floppy drive.

The following table explains which data connectors you should use when

you install additional devices.

Before Installing an

IDE Hard Disk

Refer to the drive’s installation guide to check jumper settings or if there is

a special installation procedure to follow.

Examples of multiple IDE drive combinations

Configuration

Connections to data cables

1 Hard disk drive

1. Bootable hard disk drive:

Master connector, Primary IDE Cable

2 Hard disk drives


2. Second hard disk drive:


Slave connector, Primary IDE Cable

1 Hard disk drive

1 CD-ROM drive


2. CD-ROM drive:


Master connector, Secondary IDE Cable

2 Hard disk drives

1 CD-ROM drive



3. CD-ROM drive:




1 Hard disk drive

1 CD-ROM drive

1 Zip drive


2. CD-ROM drive:

3. Zip drive:


Master connector, Secondary Cable

Slave connector, Secondary IDE Cable

2 Hard disk drives

1 CD-ROM drive

1 Zip drive



3. CD-ROM drive:

4. Zip drive:




Slave connector, Secondary IDE Cable

Section	Page
Notice	5
Important Warnings	6
Avoid Electrical Shocks	6
Electrical Connection	6
Multimedia Models	6
Removing and Replacing the Cover	6
Safety Information	7
Unpacking Your PC Workstation	7
Static Electricity	7
Information and Help	8
On HP’s Web Site	9
Downloadable Documentation from HP’s Web Site	9
Information on Ergonomic Aspects	9
Technical Information	10
Physical Characteristics (standard configuration as shipped)	10
1 Setting Up and Using Your PCWorkstation	11
Connecting Devices	12
Starting and Stopping Your PC Workstation	13
Starting Your PC Workstation for the First Time	13
Starting Your PC Workstation	13
Initializing Your Software	14
Creating an Emergency Repair Disk	14
Stopping Your PC Workstation	14
Using Your HP Enhanced Multimedia Keyboard (some models only)	15
Viewing the HP Summary Screen	16
Using the HP Setup Program	17
Starting the HP Setup Program	17
Main Menu	17
Advanced Menu	17
Security Menu	18
Boot Menu	18
Power Menu	18
Setting Passwords in the HP Setup Program	19
Setting a Password	19
Using Power Management	20
Manageability	20
Software and Drivers	20
2 Installing and Replacing Hardware Parts in Your PCWorkstation	21
Removing and Replacing the Cover and Front Bezel	22
Removing the Cover	22
Removing the Front Bezel	23
Replacing the Cover and Front Bezel	23
Replacing or Installing a Processor	24
Removing an Existing Processor	24
Installing a Processor	24
Configuring the Operating System for use with Dual Processors	26
Configuring Windows 2000	26
Configuring Windows NT 4.0 using HP DualExpress!	26
Removing, Replacing and Upgrading Memory	27
Upgrading Memory	27
Removing and Installing a Memory Module	27
Removing and Replacing an Accessory Card	29
Installing Mass Storage Devices	30
Refer to the drive’s manual to see if you must set jumpers or if there is a special installation ...	30
Cables and Connectors (all models)	30
Cables and Connectors (SCSI Models)	32
Power Connectors	33
Removing and Replacing the Primary Hard Disk Drive	34
Removing the Existing Drive	34
Installing the New Drive	34
Installing a Second Hard Disk Drive	35
Installing a Device in a Front Access Bay	36
Removing the Front Access Drive Cage	36
Installing the Device	36
Replacing the Front Access Drive Cage	37
Replacing the CD-ROM (or DVD) Drive	38
Removing the Existing Drive	38
Installing the New Drive	38
Replacing the Floppy Disk Drive	39
Removing the Floppy Disk Drive	39
Installing the Floppy Disk Drive	39
Replacing the Hard Drive Bay and Speaker Assembly	40
Removing the Assembly	40
Replacing the Assembly	41
Completing the Installation of a Mass Storage Device	42
Replacing the Main Chassis Fan	43
Removing the Fan	43
Replacing the Fan	43
Replacing the Power Supply Unit	44
Replacing the System Board	45
Removing the System Board	45
Installing the New System Board	46
System Board Switches	47
Replacing the Battery	48
3 Troubleshooting Your HP PC Workstation	49
If Your PC Does Not Start Properly	50
Pre-Boot Diagnostics	52
If You Miss the Beep Code	52
HP eDiagTools Hardware Diagnostics Utility	53
Where Can I Get HP eDiagTools?	53
Before Using HP eDiagTools	53
Starting HP eDiagTools	53
Producing a Support Ticket	54
Image Creation and Recovery CD-ROM	55
Requirements	55
Performing a Recovery, Upgrade or Downgrade	56
Running HP eDiagTools	56
Performing a Full Recovery	56
Completing a Full Recovery	57
Minimal Recovery	57
Performing a Partial Recovery	57
Frequently Asked Questions	58
Collecting Information Before Contacting HP Support	60

HP XM600 hp kayak xm600 series 2, user's guide for desktop models - Page 31

Which IDE Data, Connectors to Use, Before Installing an, IDE Hard Disk

Page 31 highlights