HP XM600 hp kayak xm600 series 2, user's guide for desktop models - Page 41

Replacing the Assembly, Reconnect the speaker and control panel cables to their connectors

Get HP XM600 - Kayak - 128 MB RAM PDF manuals and user guides View all HP XM600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

2 Installing and Replacing Hardware Parts in Your PC Workstation Replacing the Hard Drive Bay and Speaker Assembly 9 Slide the hard disk drive bay and speaker assembly towards the system board until it is well clear of the chassis edge (located between the hard disk drive bay and speaker assembly and front access cage). 10 Lift the hard disk drive bay and speaker assembly upwards to remove it from the computer. Replacing the Assembly 1 Ensure that there are no cables underneath the hard disk drive bay and speaker assembly. 2 Align the two plastic tabs (control panel side) of the hard disk drive bay and speaker assembly with their associated notches. Retention clip 3 Ensure that the plastic clips on the front of the hard disk drive bay and speaker assembly are lined-up with their associated locations. 4 From the front of the PC, gently push towards you the right-hand side of the hard disk drive bay and speaker assembly until it clicks in place. Repeat this procedure on the left-hand side of the hard disk drive bay and speaker assembly. 5 Reconnect the speaker and control panel cables to their connectors on the system board. 6 Reconnect the data and power cables. Replace the hard disk drive and hard disk drive tray. 7 Replace the PC Workstation's cover and front bezel (refer to page 23). Reconnect all the power and telecommunications cables. 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
2
Installing and Replacing Hardware Parts in Your PC Workstation
Replacing the Hard Drive Bay and Speaker Assembly
41
9
Slide the hard disk drive bay and speaker assembly towards the system
board until it is well clear of the chassis edge (located between the hard
disk drive bay and speaker assembly and front access cage).
10
Lift the hard disk drive bay and speaker assembly upwards to remove it
from the computer.
Replacing the Assembly
1
Ensure that there are no cables underneath the hard disk drive bay and
speaker assembly.
2
Align the two plastic tabs (control panel side) of the hard disk drive bay
and speaker assembly with their associated notches.
3
Ensure that the plastic clips on the front of the hard disk drive bay and
speaker assembly are lined-up with their associated locations.
4
From the front of the PC, gently push towards you the right-hand side of
the hard disk drive bay and speaker assembly until it clicks in place.
Repeat this procedure on the left-hand side of the hard disk drive bay
and speaker assembly.
5
Reconnect the speaker and control panel cables to their connectors on
the system board.
6
Reconnect the data and power cables. Replace the hard disk drive and
hard disk drive tray.
7
Replace the PC Workstation’s cover and front bezel (refer to page 23).
Reconnect all the power and telecommunications cables.
Retention clip