HP Xw9300 HP xw9300 Service and Technical Reference Guide - Page 102
Lower the PCI, Remove the PCI slot cover
View all HP Xw9300 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 102 highlights
NOTE: The following illustration shows a PCI card being installed in a PCI slot. A PCI-X card must be installed in a PCI-X slot. To install a PCI or PCI-X card: 1. Disconnect power from the system (page 79), remove the access panel (page 86), and remove the PCI card support (page 98). 2. Lift the PCI levers 1 by first pressing down and then up. 3. Remove the PCI slot cover 2. 4. Lower the PCI 3 card into the chassis. Verify that the keyed components of the card align with the socket. 5. Close the PCI levers 4. If the PCI levers do not close, be sure all cards are properly seated and then try again. 102 Removal and Replacement Procedures
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
Removal and Replacement Procedures
102
NOTE:
The following illustration shows a PCI card being installed in a PCI slot. A PCI-X card must be
installed in a PCI-X slot.
To install a PCI or PCI-X card:
1.
Disconnect power from the system (
page 79
), remove the access panel (
page 86
), and remove the PCI
card support (
page 98
).
2.
Lift the PCI levers
1
by first pressing down and then up.
3.
Remove the PCI slot cover
2
.
4.
Lower the PCI
3
card into the chassis. Verify that the keyed components of the card align with the
socket.
5.
Close the PCI levers
4
. If the PCI levers do not close, be sure all cards are properly seated and then
try again.