HP Xw9300 HP xw9300 Service and Technical Reference Guide - Page 86
Access Panel
View all HP Xw9300 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 86 highlights
Access Panel Before accessing the internal components of the workstation, the access panel must be removed. To remove the access panel: WARNING! Before removing the workstation access panel, be sure that the workstation is turned off and that the power cord is disconnected from the electrical outlet. 1. Disconnect power from the system (page 79) and lay the workstation on its side as shown. 2. If necessary, unlock the access panel (page 84). The keys are on the rear panel. 3. Pull up 1 on the handle and lift off 2 the cover. To replace the access panel, slide the cover back on until it snaps into place. 86 Removal and Replacement Procedures
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
Removal and Replacement Procedures
86
Access Panel
Before accessing the internal components of the workstation, the access panel must be removed.
To remove the access panel:
WARNING!
Before removing the workstation access panel, be sure that the workstation is turned off and
that the power cord is disconnected from the electrical outlet.
1.
Disconnect power from the system (
page 79
) and lay the workstation on its side as shown.
2.
If necessary, unlock the access panel (
page 84
). The keys are on the rear panel.
3.
Pull up
1
on the handle and lift off
2
the cover.
To replace the access panel, slide the cover back on until it snaps into place.