HP Xw9300 HP xw9300 Service and Technical Reference Guide - Page 110

The cable must stay between the system board and the hard drive cage. It might be necessary

Get HP Xw9300 - Workstation - 1 GB RAM PDF manuals and user guides View all HP Xw9300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 110 highlights

To replace a diskette drive: 1. Slide the diskette drive into the bracket and secure with two M3 screws in the rearmost holes. 2. Slide the optical drive into the bay until it stops. Lift the green drivelock release lever and push the drive in a few more inches, then release the lever and slide the drive completely into the bay until the drive is secured. 3. Connect the data cable to the diskette drive 1 and to the system board 2. Route the data cable between the system board and the hard drive cage. Your cable might look different than the one shown. CAUTION: The cable must stay between the system board and the hard drive cage. It might be necessary to push the cable down so that it catches on the system board. This routing method is important because you do not want to interfere with the CPU heatsink fans or block airflow. 4. Connect the power cable to the diskette drive. 110 Removal and Replacement Procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
Removal and Replacement Procedures
110
To replace a diskette drive:
1.
Slide the diskette drive into the bracket and secure with two M3 screws in the rearmost holes.
2.
Slide the optical drive into the bay until it stops. Lift the green drivelock release lever and push the drive
in a few more inches, then release the lever and slide the drive completely into the bay until the drive is
secured.
3.
Connect the data cable to the diskette drive
1
and to the system board
2
. Route the data cable
between the system board and the hard drive cage. Your cable might look different than the one
shown.
CAUTION:
The cable must stay between the system board and the hard drive cage. It might be necessary
to push the cable down so that it catches on the system board. This routing method is important because
you do not want to interfere with the CPU heatsink fans or block airflow.
4.
Connect the power cable to the diskette drive.