Honeywell NX4S1 Installation Guide - Page 11

NetAXS™ NX4S1 Installation - user guide

Get Honeywell NX4S1 PDF manuals and user guides View all Honeywell NX4S1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

NetAXS™ NX4S1 Installation 1.0 Notices 1.1 Warnings and Cautions Warning: Fire Safety and Liability Notice: Never connect card readers to any critical entry, exit door, barrier, elevator or gate without providing an alternative exit in accordance with all fire and life safety codes pertinent to the installation. These fire and safety codes vary from city to city and you must get approval from local fire officials whenever using an electronic product to control a door or other barrier. Use of egress buttons, for example, may be illegal in some cities. In most applications, single action exit without prior knowledge of what to do is a life safety requirement. Always make certain that any required approvals are obtained in writing. Verbal approvals are not valid. Warning: Honeywell Access Systems (HAS) never recommends using WIN-PAK or related products for use as a primary warning or monitoring system. Primary warning or monitoring systems should always meet local fire and safety code requirements. The installer must also test the system on a regular basis by instructing the end user in appropriate daily testing procedures. Failure to test a system regularly could make installer liable for damages to the end user if a problem occurs. Warning: Earth ground all enclosures for proper installation. Warning: Use suppressors on all door locks. Use HAS (part number S-4) suppressors for installation. Honeywell recommends only DC locks. Warning: Personal injury or death could occur, and the equipment could be damaged beyond repair, if this precaution is not observed! • Before installation, turn off the external circuit breaker which supplies power to the system, including door locks. • Before connecting the device to the power supply, verify that the output voltage is within specifications of the power supply. • Do not apply power to the system until after the installation has been completed. Caution: If any damage to the shipment is noticed, a claim must be filed with the commercial carrier responsible. Caution: Electro-static discharge (ESD) can damage CMOS integrated circuits and modules. To prevent damage always follow these procedures: NetAXS Access Control Unit NX4S1 Installation Guide, Document 800-00008, Revision A 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
NetAXS Access Control Unit NX4S1 Installation Guide
,
Document 800-00008, Revision A
1
NetAXS™ NX4S1 Installation
1.0
Notices
1.1
Warnings and Cautions
Warning:
Fire Safety and Liability Notice: Never connect card readers to any critical
entry, exit door, barrier, elevator or gate without providing an alternative exit in
accordance with all fire and life safety codes pertinent to the installation. These fire
and safety codes vary from city to city and you must get approval from local fire
officials whenever using an electronic product to control a door or other barrier. Use of
egress buttons, for example, may be illegal in some cities. In most applications, single
action exit without prior knowledge of what to do is a life safety requirement. Always
make certain that any required approvals are obtained in writing. Verbal approvals are
not valid.
Warning:
Honeywell Access Systems (HAS) never recommends using WIN-PAK or
related products for use as a primary warning or monitoring system. Primary warning
or monitoring systems should always meet local fire and safety code requirements.
The installer must also test the system on a regular basis by instructing the end user in
appropriate daily testing procedures. Failure to test a system regularly could make
installer liable for damages to the end user if a problem occurs.
Warning:
Earth ground all enclosures for proper installation.
Warning:
Use suppressors on all door locks. Use HAS (part number S-4) suppressors
for installation. Honeywell recommends only DC locks.
Warning:
Personal injury or death could occur, and the equipment could be damaged
beyond repair, if this precaution is not observed!
•
Before installation, turn off the external circuit breaker which supplies power
to the system, including door locks.
•
Before connecting the device to the power supply, verify that the output
voltage is within specifications of the power supply.
•
Do not apply power to the system until after the installation has been
completed.
Caution:
If any damage to the shipment is noticed, a claim must be filed with the
commercial carrier responsible.
Caution:
Electro-static discharge (ESD) can damage CMOS integrated circuits and
modules. To prevent damage always follow these procedures: