Honeywell NX4S1 Installation Guide - Page 62

Standalone Settings

Get Honeywell NX4S1 PDF manuals and user guides View all Honeywell NX4S1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

NetAXS™ Standalone Operation Standalone Settings A.2 Standalone Settings A.2.1 NetAXS™ Panel Hardware Settings • Configure the system with an RS-232 connection according to Figure 20 on page 30. • Set DIP switches 1 through 5 to define the panel number (see Table 3 on page 22). Panel number 0 is not valid. • Set DIP switch 6 to the OFF position to place the panel into the Multidrop mode. • Use a personal computer's serial communications port (COM1 or COM2) and a terminal emulation program to configure the NetAXS™ panel for normal operation. A.2.2 Communication Settings • Baud Rate: 115200 • Data Bits: 8 • Parity: None • Stop Bits: 1 • Flow Control: None A.2.3 Emulation Settings • Echo typed characters locally: YES • Line Delay: 500 milliseconds A.2.4 Verifying Communications 1. Press the spacebar. 2. Press the carriage return . "S?" apppear for every online panel and indicates proper communication between the terminal and panel. 52 www.honeywell.com

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
52
www.honeywell.com
NetAXS™ Standalone Operation
Standalone Settings
A.2
Standalone Settings
A.2.1
NetAXS™ Panel Hardware Settings
•
Configure the system with an RS-232 connection according to
Figure 20
on
page 30.
•
Set DIP switches 1 through 5 to define the panel number (see
Table 3
on
page 22).
Panel number 0 is not valid.
•
Set DIP switch 6 to the OFF position to place the panel into the Multidrop
mode.
•
Use a personal computer’s serial communications port (COM1 or COM2) and
a terminal emulation program to configure the NetAXS™ panel for normal
operation.
A.2.2
Communication Settings
•
Baud Rate: 115200
•
Data Bits: 8
•
Parity: None
•
Stop Bits: 1
•
Flow Control: None
A.2.3
Emulation Settings
•
Echo typed characters locally: YES
•
Line Delay: 500 milliseconds
A.2.4
Verifying Communications
1.
Press the spacebar.
2.
Press the carriage return <CR>. “S?” apppear for every online panel and
indicates proper communication between the terminal and panel.