Honeywell NX4S1 Installation Guide - Page 63

Standalone Commands

Get Honeywell NX4S1 PDF manuals and user guides View all Honeywell NX4S1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

NetAXS™ Standalone Operation Standalone Commands A.3 Standalone Commands Use the following commands, in the order they are listed, to configure the NetAXS™ panel. 1. T command: Sets the panel's Time 2. D command: Sets the panel's Date 3. L command: Creates Time zones for use by the cards 4. C command: Adds or Deletes cards from the panel 5. W command: Program each input for either NO/NC and Supervised or NON Supervised operation 6. P command: Sets interlocks between input points and/or output points Note: In all examples, the underbar "_" indicates a "space" character and indicates a carriage return. A.3.1 T (Time) Command _T=pn_hh:mm Variables: pn = panel number (1-31) hh = hours (0-23) (Military time) mm = minutes (00-59) Example #1: _T=1_08:30 This command would set panel 1 to a time of 8:30 AM. Example #2 _T=6_18:15 This command would set panel 6 to a time of 6:15 PM. NetAXS Access Control Unit NX4L1 Installation Guide, 7-901099, Revision A 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
NetAXS™ Standalone Operation
Standalone Commands
NetAXS Access Control Unit NX4L1 Installation Guide
,
7-901099, Revision A
53
A.3
Standalone Commands
Use the following commands, in the order they are listed, to configure the NetAXS™
panel.
1.
T command: Sets the panel’s Time
2.
D command: Sets the panel’s Date
3.
L command: Creates Time zones for use by the cards
4.
C command: Adds or Deletes cards from the panel
5.
W command: Program each input for either NO/NC and Supervised or NON
Supervised operation
6.
P command: Sets interlocks between input points and/or output points
Note:
In all examples, the underbar “_” indicates a “space” character and <CR>
indicates a carriage return.
A.3.1
T (Time) Command
_T=pn_hh:mm<CR>
Variables:
pn = panel number (1-31)
hh = hours (0-23) (Military time)
mm = minutes (00-59)
Example #1:
_T=1_08:30<CR>
This command would set panel 1 to a time of 8:30 AM.
Example #2
_T=6_18:15<CR>
This command would set panel 6 to a time of 6:15 PM.