Home » Honeywell Manuals » Security Monitors & Recorders » Honeywell NX4S1 » Manual Viewer

Honeywell NX4S1 Installation Guide - Page 51

NetAXS™/NetAXS™ Access Controller Panel Connection Detail

Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

NetAXS™ NX4S1 Installation System Configuration 5.15 NetAXS™/NetAXS™ Access Controller Panel Connection Detail Figure 31: NetAXS™/NetAXS™ Access Controller Panel Connection Detail Ground Shield X DO NOT CONNECT or GROUND SHIELD To Serial Connection NetAXS TB7 1 2 3 NetAXS TB7 1 2 3 DIP Switch Settings S1-S5:Panel Address S6: ON J36: CLOSED J37: CLOSED DIP Switch Settings S1-S5:Panel Address S6: OFF J36: CLOSED J37: CLOSED DIP Switch Settings S1-S5:Panel Address S6: OFF J36: OPEN J37: OPEN NetAXS Panel 3 1 2 DO NOT CONNECT SHIELD X 485 Common Shield 485 + 485 - NetAXS TB7 Ground only one side of cable shield 4,000 ft.(1,200 m) max,24 AWG,2 twisted pairs with shield,120 ohm,23 pf (NCI part no.NCP2441-TN) NetAXS Access Control Unit NX4S1 Installation Guide, Document 800-00008, Revision A 41

Section	Page
Table of Contents	3
List of Figures	7
List of Tables	9
NetAXS™ NX4S1 Installation	11
1.0 Notices	11
1.1 Warnings and Cautions	11
1.2 Product Liability, Mutual Indemnification	12
1.3 Limited Warranty	12
1.4 Federal Communications Commission	13
1.5 Industry Canada	13
1.6 Underwriters Laboratories Incorporated	14
2.0 Introduction	15
2.1 Access Control Overview	15
2.2 NetAXS™ Access Overview	15
3.0 Panel Components and Descriptions	16
3.1 NetAXS™ Access Control Unit	17
Real-Time Clock Protection	17
Memory Protection	17
Reader and AUX Power	17
3.2 Power Supply	18
3.3 Battery	18
3.4 Enclosure	18
3.5 Suppressors	18
4.0 Installation	19
4.1 Cabinet Mounting	20
4.2 Reader Wiring	24
4.3 Supervised Input Wiring	24
4.4 NX4S1 Control Output Wiring	26
4.5 Communications	26
RS-232 Communications	26
RS-485 Communications	28
Ethernet TCP/IP Communications	29
4.6 DIP Switch Settings	31
4.7 Jumper Settings	33
4.8 Downstream I/O	33
5.0 System Configuration	36
5.1 RS-485 Connection via PCI-2	36
5.2 RS-485 Connection via NetAXS™	37
5.3 RS-485 Connections with Multidrop Panels at Both Ends of the Cable	38
5.4 RS-232 Connection	40
5.5 Ethernet Connection	41
5.6 LANSRLU1 Connection	42
5.7 RS-485 Short Haul Modem Connection via PCI-2	43
5.8 RS-485 Short Haul Modem Connection via NetAXS™	44
5.9 RS-232 Short Haul Modem Connection	45
5.10 M-56K Dial-up Modem, RS-485 Connection via Hub	46
5.11 M-56K Dial-up Modem, RS-485 Connection via NetAXS™	47
5.12 Fiber Converter to RS-485 Connection via PCI-2	48
5.13 Fiber Converter to RS-485 Connection via NetAXS™	49
5.14 N-485-PCI-2/NetAXS™ Access Controller Panel Connection Detail	50
5.15 NetAXS™/NetAXS™ Access Controller Panel Connection Detail	51
6.0 NetAXS™ Startup	52
6.1 LED Operation	52
7.0 Hardware Specifications	54
7.1 Relay Contacts	54
7.2 Reader Interface	54
7.3 NX4S1 Wire Requirements	54
7.4 Maximum Output Loading	54
7.5 Common Connections	55
7.6 Mechanical	55
7.7 Environment	55
7.8 Communications and Wiring	56
7.9 Reader Wiring	56
7.10 NX4S1 Wiring Diagram	57
8.0 Maintenance	58
9.0 Troubleshooting	58
10.0 Technical Support	59
10.1 Normal Support Hours	59
10.2 Web	59
NetAXS™ Standalone Operation	61
A.1 Basic Standalone Operations	61
A.1.1 Card Read / Door Lock Operation	61
A.1.2 Door Egress / Door Lock / Door Status Operation	61
A.2 Standalone Settings	62
A.2.1 NetAXS™ Panel Hardware Settings	62
A.2.2 Communication Settings	62
A.2.3 Emulation Settings	62
A.2.4 Verifying Communications	62
A.3 Standalone Commands	63
A.3.1 T (Time) Command	63
A.3.2 D (Date) Command	64
A.3.3 L (Time Zone) Command	65
A.3.4 C (Card Add) Command	66
A.3.5 C (Card Delete) Command	66
A.3.6 W (Input) Command	67
A.3.7 P (Interlock) Command	67
A.3.8 Flow Control Disable/Enable	68
A.4 NetAXS™ Panel Defaults	69
A.4.1 Reader Ports	69
A.4.2 Reader LED Outputs	69
A.4.3 Reader Tamper Inputs	70
A.4.4 Door Egress Inputs	70
A.4.5 Door Status Inputs	71
A.4.6 ACFAIL and Panel Tamper Inputs	71