Kenwood DNX875S User Manual - Page 92

Supplied accessories for, installation, Installation procedure, Connection/Installation

Get Kenwood DNX875S PDF manuals and user guides View all Kenwood DNX875S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

Connection/Installation • Do not press hard on the panel surface when 9 installing the unit to the vehicle. Otherwise scars, damage, or failure may result. • Reception may drop if there are metal objects near the Bluetooth antenna. 0 (3.5 m) x1 Bluetooth antenna unit ÑÑSupplied accessories for installation 1 x1 2 (Black 1 m) x1 3 (Gray 1 m) x1 4 (3 m) x1 5 [1] x2 6 (M5 x 8 mm) x6 7 (M5 x 8 mm) x6 8 [1] x1 - [1] x1 = [1] x4 [1] DNX995S only ÑÑInstallation procedure 1) To prevent a short circuit, remove the key from the ignition and disconnect the ¤ terminal of the battery. 2) Make the proper input and output wire connections for each unit. 3) Connect the speaker wires of the wiring harness. 4) Connect the wiring harness wires in the following order; ground, battery, ignition. 5) Connect the wiring harness connector to the unit. 6) Install the unit in your car. 7) Reconnect the ¤ terminal of the battery. 8) Perform the Initial Setup. See Initial setup (P.9). x1 92

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
Connection/Installation
92
• Do not press hard on the panel surface when
installing the unit to the vehicle. Otherwise
scars, damage, or failure may result.
• Reception may drop if there are metal objects
near the Bluetooth antenna.
Bluetooth antenna unit
Ñ
Supplied accessories for
installation
1
x1
2
(Black 1 m)
x1
3
(Gray 1 m)
x1
4
(3 m)
x1
5
[1]
x2
6
(M5 x 8 mm)
x6
7
(M5 x 8 mm)
x6
8
[1]
x1
9
(3.5 m)
x1
0
x1
-
[1]
x1
=
[1]
x4
[1]
DNX995S only
Ñ
Installation procedure
1) To prevent a short circuit, remove the key
from the ignition and disconnect the
¤
terminal of the battery.
2) Make the proper input and output wire
connections for each unit.
3) Connect the speaker wires of the wiring
harness.
4) Connect the wiring harness wires in the
following order; ground, battery, ignition.
5) Connect the wiring harness connector to the
unit.
6) Install the unit in your car.
7) Reconnect the
¤
terminal of the battery.
8) Perform the Initial Setup.
See
Initial setup (P.9)
.