Konica Minolta ProJet 160 Cube3 User Guide - Page 7

Important Safety Information - 3d printer

Get Konica Minolta ProJet 160 PDF manuals and user guides View all Konica Minolta ProJet 160 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

2 IMPORTANT SAFETY INFORMATION SAFETY SYMBOLS AND DEFINITIONS HOT SURFACE HAZARD: A HOT SURFACE IS ACCESSIBLE IN THE VICINITY OF THIS SIGN OR AT THE PRINT JET. AVOID CONTACT WITH THESE AREAS. HOT SURFACES CAN CAUSE SEVERE BURNS. Caution: Indicates something may happen that could cause loss of data, damage to equipment, or could cause personal injury. Caution: Indicates a pinch point hazard that could cause personal injury. SHOCK WARNING: INDICATES A POTENTIAL SHOCK HAZARD. SAFETY GUIDELINES • Follow all safety rules in this section and observe all cautions and warnings in this guide. • DO NOT modify any safety features or make modifications to the Cube. Doing so is prohibited and voids the manufacturer's war- ranty. • Use of print materials, or 3D prints other than 3D Systems' print materials and genuine 3D Systems' components may void the warranty. • Adult supervision is required; observe children closely and intervene as necessary to prevent potential safety problems and ensure the Cube's appropriate use. Ensure small 3D prints are not accessible to young children. These 3D prints are potential choking hazards for young children. • DO NOT change a material cartridge during printing; doing so may damage the Cube. HOT SURFACE HAZARD: DO NOT TOUCH THE PRINT JETS DURING SETUP AND OPERATION. THE PRINT JETS BECOME VERY HOT. Caution: DO NOT disconnect the CUBE from utility power while the printhead is hot. Wait until the print jet's amber light turns off before disconnecting from utility power as this may damage the print jet. Caution: Read and follow all instructions prior to setting up the printer. SHOCK WARNING: DUE TO RISK OF SHOCK, AVOID CONTACT WITH ALL INTERNAL ELECTRONIC COMPONENTS. WARNING: THE CUBE SHOULD ONLY BE SERVICED BY AUTHORIZED SERVICE TECHNICIANS. PRIOR TO ANY PART REPLACEMENT PROCEDURE, THE PRINTER MUST BE POWERED OFF AND DISCONNECTED FROM UTILITY POWER. WARNING: HAZARDOUS MOVING PARTS. KEEP FINGERS AND OTHER BODY PARTS AWAY. To ensure safety, please exercise caution when operating your Cube. Read and follow all safety precautions as outlined in this user guide. Be careful when operating your Cube 3D Printer to ensure proper printing and be mindful of and avoid hot surfaces. 3D Systems, Inc. 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
3
3D Systems, Inc
.
2
IMPORTANT SAFETY INFORMATION
SAFETY SYMBOLS AND DEFINITIONS
HOT SURFACE HAZARD: A HOT SURFACE IS ACCESSIBLE IN THE VICINITY OF THIS SIGN OR AT THE PRINT
JET° AVOID CONTACT WITH THESE AREAS° HOT SURFACES CAN CAUSE SEVERE BURNS°
Caution: Indicates something may happen that could cause loss of data, damage to equipment, or could cause
personal injury°
Caution: Indicates a pinch point hazard that could cause personal injury°
SHOCK WARNING: INDICATES A POTENTIAL SHOCK HAZARD°
SAFETY GUIDELINES
•
Follow all safety rules in this section and observe all cautions and warnings in this guide°
•
DO NOT modify any safety features or make modifications to the Cube. Doing so is prohibited and voids the manufacturer’s war
-
ranty°
•
Use of print materials, or 3D prints other than 3D Systems’ print materials and genuine 3D Systems’ components may void the
warranty°
•
Adult supervision is required; observe children closely and intervene as necessary to prevent potential safety problems and ensure
the Cube’s appropriate use° Ensure small 3D prints are not accessible to young children° These 3D prints are potential choking
hazards for young children°
•
DO NOT change a material cartridge during printing; doing so may damage the Cube°
HOT SURFACE HAZARD: DO NOT TOUCH THE PRINT JETS DURING SETUP AND OPERATION° THE PRINT JETS
BECOME VERY HOT°
Caution: DO NOT disconnect the CUBE from utility power while the printhead is hot. Wait until the print jet’s
amber light turns off before disconnecting from utility power as this may damage the print jet°
Caution: Read and follow all instructions prior to setting up the printer°
SHOCK WARNING: DUE TO RISK OF SHOCK, AVOID CONTACT WITH ALL INTERNAL ELECTRONIC
COMPONENTS°
WARNING: THE CUBE SHOULD ONLY BE SERVICED BY AUTHORIZED SERVICE TECHNICIANS° PRIOR TO ANY
PART REPLACEMENT PROCEDURE, THE PRINTER MUST BE POWERED OFF AND DISCONNECTED FROM
UTILITY POWER°
WARNING: HAZARDOUS MOVING PARTS° KEEP FINGERS AND OTHER BODY PARTS AWAY°
To ensure safety, please exercise caution when operating your Cube° Read and follow all safety precautions as outlined in this user
guide°
Be careful when operating your Cube 3D Printer to ensure proper printing and be mindful of and avoid hot surfaces°