Sharp UX-4000M Service Manual - Page 23

Rapid key 05: Paper feed aging The mode is used for aging related to the printing. In this mode, the following modes are provided. 1 Blank paper aging mode (ALL WHITE AGING) 2 Whole black print aging mode (ALL BLACK AGING) 3 4% printing aging mode (4% AGING) After selecting the paper-feed aging mode in the print diagnosis mode, input the number of each mode above with the ten-key, and the mode will be executed. The detailed specifications of each mode are described as follows. Here, the operation in each mode is stopped only when the STOP key is pressed by the operator or a printing-impossible error occurs. • Blank paper aging mode (ALL WHITE AGING) In the mode, printing is continued in the whole white (white paper) printing pattern until the STOP key is pressed by the operator. (In the printing area) • Whole black printing aging mode (ALL BLACK AGING) In the mode, printing is continued in the whole black (whole black) printing pattern until the STOP key is pressed by the operator. (In the printing area) Rapid key 06: Life set mode The mode is used to set the life counter of the printer and the counter of the auto feeder at desired values. For setting, proceed with the follow- 1ing procedure. When the life counter setting mode is selected, the following will be is displayed. # key MACH I NE = 0 0 0 1 2 3 DRUM L I F E = 0 0 0 1 2 3 L I FE1=000123 key L I FE2=000123 L I FE3=000123 FEEDER L F= 0 0 0 1 2 3 TONER L F = 0 0 0 1 2 3 The cursor blinks at the top data. Seven counters can be selected with the "#" and " " keys. 2 1 In the state , input a desired setting number of 6 digits with the tenkey. 3 After input of 6 digits, shift to another counter with the "#" and " " keys as necessary. When all necessary counters are completely input, press the START key. 4 "STORED" will be displayed with the set values stored into the memory. For checking, retry this mode. Note: This counter indicates the printer use conditions such as numbers of printed pages from the beginning of use. In the normal memory clear condition, the counter will not be reset. In conditions including damaged memory contents caused by repairing the panel, this counter should be reset or cleared in addition to the ordinary memory clear. UX-4000MU FO-2950MU/C Rapid key 07: Life all clear The mode is used to clear the life counter of the printer of the counter of the auto feeder. Note: The counter shows the operational state of the printer (e.g. how many sheets have been printed since start of use?). The ordinary memory does not reset the counter. Accordingly, it is necessary to reset this counter in addition to the ordinary memory clear if the content in the memory on the control PWB is broken because of PWB repair, etc. (In the production stage, it is necessary to execute this in the last process.) Rapid key 08: Life entry mode (For Serviceman temporary counter) The mode is used to set a desired value for the judgment value (alarm judgment counter value) of the general purpose life counters 1 thru 3 of the printer. If the life of a consumable part (developer, imprinter, etc) is set, the model which has the error display and RMS function will inform RMS when the counter reaches the set value. For setting, proceed with 1the following procedure. When the life counter entry mode is selected, the following will be displayed. # key L I FE1 =0 0 0 1 2 3 L I FE2 =0 0 0 1 2 3 key L I FE3 =0 0 0 1 2 3 The cursor blinks at the top data. Three counters can be selected with the "#" and " " keys. 2 1 In the state , input a desired setting number of 6 digits with the tenkey. 3 After input of 6 digits, shift to another counter with the "#" and " " keys as necessary. When all necessary counters are completely in- put, press the START key. 4 "STORED" will be displayed with the set values stored into the memory. For checking, retry this mode. Note: The counter shows the operational state of the printer (how many sheets have been printed since start of use? and others). The ordinary memory does not reset the counter. Accordingly, it is necessary to reset the counter or do the clear process in addition to the ordinary memory clear if the content in the memory on the control PWB is broken because of PWB repair, etc. (In the production stage, it is necessary to execute this in the last process.) Rapid key 9: Top adjust mode Adjust the top margin for printing on a page. You can enter any value from 0 to 99 using the ten-key keypad. The standard (initial) value is 50. When the setting is increased, the print start position will be moved closer to the beginning of page. When the setting is decreased, the print start position will be moved further away from the beginning of page. 2 - 7