Sony PDWF75 User Manual (PDW-F75 Professional Disc Recorder Operating Manual f - Page 85

File Operations in File Access Mode (for Macintosh), Making FAM Connections

Get Sony PDWF75 PDF manuals and user guides View all Sony PDWF75 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

Chapter 5 File Operations at least 10 seconds, and then reconnect the disconnected cable. The unit is powered off and an i.LINK cable is connected: Power the unit on. To disable FAM connections Execute one of the procedures described in the previous section "To make a reconnection" to make a FAM connection between this unit and the remote computer. To disable FAM connections, in the setup menu, set INTERFACE SELECT >i.LINK MODE to "AV/C" (see page 103). File Operations in File Access Mode (for Macintosh) File access mode operating environment Operating system requirements for file operations by file access mode are as follows. • Computer operating system: Mac OS X v10.4.11 or higher Preparations Do the following on the remote computer and this unit. • Install the FAM driver on the remote computer (see the next item). To install the FAM driver Insert the supplied CD-ROM (XDCAM Application) into the CD-ROM drive of your computer, and execute the FAM Driver >Mac >FAM Driver 1.1.1.dmg file, then follow the installation instructions. For details, refer to the ReadMe file contained on the CDROM disc. To check the FAM driver version Connect this unit to your computer with an i.LINK cable, and then, with a disc loaded, start the system profiler utility of the application. The version appears to the right of "prodisk_fs" when you select "Advanced Functions" under "Software". Making FAM Connections Proceed as follows. 1 If there is a disc loaded in this unit, put the unit into the following state. • Recording, playback, search and other disc operations: Stopped • THUMBNAIL button: Off • Disc access by clip deletion, disc formatting, or other operation: Stopped • Picture Cache function and Interval Rec function: Off • MENU button: OFF • Unsaved current clip list: Save or clear 2 Connect the S400 connector on this unit to the i.LINK (IEEE1394) connector on the remote computer, using an i.LINK cable (see page 84). 85 File Operations in File Access Mode (for Macintosh)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
85
File Operations in File Access Mode (for Macintosh)
Chapter 5
File Operations
at least 10 seconds, and then reconnect the
disconnected cable.
The unit is powered off and an i.LINK cable is
connected:
Power the unit on.
To disable FAM connections
Execute one of the procedures described in the previous
section “To make a reconnection” to make a FAM
connection between this unit and the remote computer. To
disable FAM connections, in the setup menu, set
INTERFACE SELECT >i.LINK MODE to “AV/C”
(see
page 103)
.
File Operations in File
Access Mode (for
Macintosh)
File access mode operating environment
Operating system requirements for file operations by file
access mode are as follows.
•
Computer operating system: Mac OS X v10.4.11 or
higher
Preparations
Do the following on the remote computer and this unit.
•
Install the FAM driver on the remote computer
(see the
next item)
.
To install the FAM driver
Insert the supplied CD-ROM (XDCAM Application) into
the CD-ROM drive of your computer, and execute the
FAM Driver >Mac >FAM Driver 1.1.1.dmg file, then
follow the installation instructions.
For details, refer to the ReadMe file contained on the CD-
ROM disc.
To check the FAM driver version
Connect this unit to your computer with an i.LINK cable,
and then, with a disc loaded, start the system profiler utility
of the application. The version appears to the right of
“prodisk_fs” when you select “Advanced Functions”
under “Software”.
Making FAM Connections
Proceed as follows.
1
If there is a disc loaded in this unit, put the unit into the
following state.
•
Recording, playback, search and other disc
operations: Stopped
•
THUMBNAIL button: Off
•
Disc access by clip deletion, disc formatting, or
other operation: Stopped
•
Picture Cache function and Interval Rec function:
Off
•
MENU button: OFF
•
Unsaved current clip list: Save or clear
2
Connect the
S400 connector on this unit to the
i.LINK (IEEE1394) connector on the remote
computer, using an i.LINK cable
(see page 84)
.